Replacement Hub and Brake Assemblies that Fit Sure Trac 3,500 lb Axle

Question

Question:

I have trailer with 3500LB Sure Trac axle that I need complete new brakes for. Will the following work? AKEBRK-35-SA AKHD-545-35-K Thank you

asked by: Sam G

0

Expert Reply:

Hey Sam, so from previous customers we have determined that the Sure Trac axles use the standard trailer axle components so yes the brake assemblies part # AKEBRK-35-SA and the hub part # AKHD-545-35-K would fit and work great.

expert reply by: Jameson C

0

Answer 1

While grade 8 bolts like you have are recommended to install a class 3 trailer hitch, I do not recommend using the bolts in your picture. For a trailer hitch like the Curt #14001 you were looking at, it uses 1/2" x 13 grade 8 bolts. Hitch…

view full answer...

Answer 2

The difference between the two is the bolt hole distance relative to the top of the coupler. The part #F223000301 is 1 inch from the top of the coupler to the ball hole whereas the part #F233000301 has a distance of 3/4 inch like what you are in need…

view full answer...

Answer 3

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

Yes, the Electric Trailer Brake Kit - Self-Adjusting #AKEBRK-35-SA that you referenced are an exact replacement for the AxleTek assemblies you have now that have Axletek-10-GG stamped on them. If you check out the attached picture you can see the…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hi Rusty; the Dexter #84546UC3-EZ and etrailer #AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern…

view full answer...

Answer 8

I think I have a solution for you in the Global Link RV Entry Door Locking Latch Kit, #295-000021 for white or, #295-000019 for black. This latch kit measures 3.47" wide x 4.28" tall, fits doors that are 1-1/4" to 1-1/2" thick,…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Phillip, since we know you have 3,500 lb axles we can help but it's not based on the VIN. Since we don't know what brake assembly brand you have on your trailer but we do know capacity the correct replacement assemblies are the part…

view full answer...

Answer 11

Hey Jared, If your axle has a brake flange like I have pictured below then you would be able to mount a 3,500lb brake assembly #AKEBRK-35 (manual-adjust) or #AKEBRK-35-SA (self-adjust). You'll also need to replace your idler hubs with drums so…

view full answer...

Answer 12

When adding brakes to a trailer the first thing you will need is to determine if there is a brake mounting flange on the axle. If you do not have a brake flange I recommend part #4-35. This should be welded in place by a professional welder because…

view full answer...

Replacement Hub and Brake Assemblies that Fit Sure Trac 3,500 lb Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching