Recommended Replacement Reverse Lockout Solenoid for a Demco DA70 Actuator

Question

Question:

Hello, I was wonder which reverse lockout solenoid would I need for a DA70 actuator?

asked by: Kevin M

0

Expert Reply:

Hey Kevin, for your Demco DA70 actuator you can use the Reverse Lockout Solenoid for Demco Hydraulic Brake Actuators # DM11993.

expert reply by: Bryce D

0

Richard T.

4/14/2024

Is there a solenoid cover available for the parts you reference above?

Bryce D.

4/15/2024

@RichardT Yes Richard you can use the Replacement Solenoid Cover for Demco Hydraulic Brake Actuators with Electric Lockout # DM11674-95.

Answer 1

The Atwood couplers have been discontinued for a bit so you'll be hard-pressed to find any replacement parts for them. We don't have any replacement parts for them anymore so I recommend just replacing the whole coupler with something…

view full answer...

Answer 2

There isn't an angle I can give you for when the lockout would be needed; however, if you want to be able to back up as needed you will need a reverse lockout with the Demco Hydraulic Brake Actuator #DM8609502. That said, the Manual Reverse…

view full answer...

Answer 3

You can use the manual lock out part #DM5939 to manually lock out the Demco DA91 actuator part #DM8164311 that you referenced.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Recommended Replacement Reverse Lockout Solenoid for a Demco DA70 Actuator

Product Page this Question was Asked From

Continue Researching