Replacement Brake Kit, Surge Actuator, and Bearing Kit for a 1988 EZ Loader Boat Trailer
Updated 03/19/2024 | Published 03/18/2024 >
Products Featured in This Question
Question:
I am looking at replacement brake drums for a 1988 EZ Loader boat trailer equipped with drum surge brakes but dont know if the axle cabacity is 3500 lbs or 3750 lbs. Reviewing your videos, it appears the 3750 has riveted brake pads. Can I put the 3750 lbs kit on a 3500lb axle? Also, I will be replacing the master cylinder. The unit removed is a Atwood 85736. Are these still made or do I need to replace the entire unit? Finally, how do I determine what replacement bearing kit to purchase? It is a 10inch drum with 5 studs. Thank you!
asked by: Scott M
Helpful Expert Reply:
Hey Scott!
Both the 3,500 lb and 3,750 lb brake assemblies work with a 10" x 2-1/4" drum so either one will fit with your hubs, but you can verify your axle capacity either on the sticker tag on the side of your EZ Loader Trailer, or by looking at the tag in the middle of your axle(s).
One you know what weight capacity you have then I recommend getting Free-Backing brakes so you'll be able to back the trailer up. For 3,500 lb brake assemblies this will be part # AKFBBRK-35 and for 3,750 lb brake assemblies it will be part # T4071600-500.
Atwood went out of the coupler business a number of years ago so there aren't any direct replacement master cylinders. To replace your surge brake actuator you can use either the bolt-on # DM72VR or a weld-on for an A-Frame # DM8609502.
Finally, for a replacement bearing kit you should need the kit # BK2-100 for a #84 spindle. You can verify this kit will fit your application by comparing the parts you remove with the following:
- Inner Bearing L68149
- Outer Bearing L44649
- Grease Seal ID 1.719" and OD 2.565"
Product Page this Question was Asked From
Hydraulic Trailer Brake Kit - Uni-Servo - Free Backing - 10" - Left/Right Hand - 3,500 lbs
- Trailer Brakes
- Hydraulic Drum Brakes
- Standard Grade
- Free Backing
- Manual Adjust
- Single Servo
- 10 x 2-1/4 Inch Drum
- 3500 lbs Axle
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Continue Researching
- Search Results: brake actuator
- Search Results: tang washer
- Search Results: trailer safety chains
- Shop: Lippert Complete Bearing Kit for 3.5K Trailer Axles - L44649/L68149 Bearings, L44610/L68111 Races
- Q&A: Replacement For Atwood 83000, 83010 Drum Brake Actuator & 10 Inch Free Backing Drum Brakes
- Video: Easy Grease Trailer Hub/Drum Assembly for 3.5K Axles Feature Review
- Shop: Easy Grease Trailer Hub/Drum Assembly for 3.5K Axles - 10" Diameter - 5 on 4-1/2 - Galvanized
- Shop: Lippert ABS Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4.5 - Pre-Greased
- Shop: Dexter DX7.5 Drop-N-Go Brake Actuator - Drum Brakes - 2" Ball - Zinc Plated - 7,500 lbs
- Q&A: What Are The Mounting Hole Dimensions Of The Demco Hydraulic Surge Brake Actuator DM8609101
- Shop: Terran Industries Rubber Plug for Dust Caps - 2K to 8K Trailer Axles
- Article: How to Bleed Your Trailer Surge Brakes
- Video: Feature Review Dexter DX7.5 Drop-N-Go Brake Actuator
- Video: Demco Hydraulic Brake Actuator-DM8609101 Feature Review
- Video: Feature Breakdown: Dexter DX7.5 Drop-N-Go Brake Actuator
- Video: Hands-On with the 48" Long Safety Chain with 1/4" S-Hook
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Replacement Spindle Washer - Tang Type for E-Z Lube
- Q&A: How Does Breakaway of Dexter A-60 Actuator get Reset
- Q&A: Parts Needed to Add Electric Brakes to a 6x10 Trailer
- Video: Dexter Hydraulic Brake Kit Spec Review
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Search Results: trailer tires and wheels
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?

