Where to Measure for etrailer Tandem Axle Fender Width

Question

Question:

where do you measure the double axel trailer fenders from for the length

asked by: Kirk K

0

Expert Reply:

Hey Kirk!

We measure from the outside to the outside on the Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers # HP44VR (see attached photo).

expert reply by: Jon G

0

Where to Measure for Tandem Axle Fender Width
(click to enlarge)

Answer 1

I have attached a photo that shows how you determine where the centerline should be between your axles. When determining axle placement, an important factor to consider is the tongue weight. You want the tongue weight of the trailer to be…

view full answer...

Answer 2

The length of a fender is measured from the longest point, at the very bottom of each end across. Then the height is measured from the tallest point, right in the center. For example, the CE Smith Single Axle Trailer Fender #CE17720 is 22-1/2"…

view full answer...

Answer 3

Trailer fenders are classified by the diameter of the trailer wheels they're compatible with. For instance, the #F008583 fender you referenced works with 13 inch diameter wheels. If you're unsure of the diameter of your wheels, the last two…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Where to Measure for etrailer Tandem Axle Fender Width

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching