Parts Needed to install Brake Controller in 2017 Ford Expedition

Question

Question:

I have a 2017 Ford Expedition XLT 4WD 6 Cylinders T 3.5L DI Turbo DOHC 213 CID VIN: 1FMJU1JT9HEA55371 I would like to get the towing wiring updated and a brake assist installed. Get it ready for an RV. I would like an estimate for this please. Thanks, Dave

asked by: David R

0

Expert Reply:

Hey Dave, your 2017 Ford Expedition would have came with a factory 7-way trailer wiring harness so to update your wiring so that you can install a brake controller all you need is the correct harness that plugs into the port under your dash like the # 22292 so you can install a controller like the P3 part # 90195 and you'd be set.

expert reply by: Jameson C

0

Dave

3/11/2024

Hey! You'd think it would have the newer plug but I just verified, it's the 4 pin rectangle. I'm guessing that should be updated? What would all cost? Please and thank you, Dave

Jameson C.

3/11/2024

@Dave Okay so you can still use the part numbers that were mentioned but you would also need the part # 37185 to convert the 4-way to a 7-way and you'll need to run a wire from it to the bundle of wires near your spare tire under the truck. See attached attached link for more info on this.

Helpful Links

faq-fbc_sd05.aspx

Dave

3/14/2024

@JamesonC I apologize. I tried to send you some photos but I might have given you the wrong description. It's not even a 4 pin connector. There is only 3 pins in this connector. Is that going to be an issue? All the same parts?

Jameson C.

3/14/2024

@Dave It still sounds like it may be a 4-way that you have. Does it look like the part # 18004?

See All (5) Replies to Dave ∨

Answer 1

Your 2016 Toyota Sienna can use a weight distribution hitch so long as your trailer hitch is rated for use with weight distribution; since you mentioned you have a Curt, their hitch that fits your '16 Sienna, has the same ratings as yours, and is…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 7

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 8

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

No, it will not Bryan. The Redarc Tow-Pro Link item #RED57AR requires a USCAR port that comes with factory tow packages. The Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit item #SH25VR, that fits your 2023 BMW X5, does not have this…

view full answer...

Parts Needed to install Brake Controller in 2017 Ford Expedition

Continue Researching