Inner and Outer Diameter of the Yates Spool Roller for Boat Trailers

Question

Question:

Hello, for part # yr8302-4p, what is the inner OD, the narrow part of the roller? Thank you, Peter

asked by: Peter P

0

Expert Reply:

Hey Peter, I actually went out to the warehouse and measured the Yates Spool Roller for Boat Trailers # YR8302-4P and measured 51 mm for the inner and 75 mm for the outer.

expert reply by: Bryce D

0

Yates Spool Roller Inner and Outer Diameter
(click to enlarge)

Answer 1

Trailer tires should be inflated when they are cold and should be inflated to the max psi rating on the sidewall. In your case you would want to run 80 psi. If you don't inflate them to the max psi figure you will lose weight capacity and…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 12

Hey Jairo. So we do not offer a direct replacement for the Norcold N611, but we do have a good replacement option for you. It really comes down to what will fit in your cutout space. Take a look at the Norcold RV Refrigerator w/ Freezer - 8.2 cu ft -…

view full answer...

Inner and Outer Diameter of the Yates Spool Roller for Boat Trailers

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching