Function of Brown Wire on 7-Way on Homemade Flatbed Trailer

Question

Question:

Hooking up my trailer wires into the 7 pin connector. I am replacing my 7 pin cord and connection box, but unfortunately when I took my connection box out I forgot to take a picture of where the wires had been attached. It is a homemade flatbed trailer. The wires are yellow/brown, green/brown and another brown. I tied the y/b into the left signal/brake red at the connector box and the green/brown into the right signal/brake brown at the connector box. Nothing, no power. And what is the extra brown for???

asked by: Nora C

0

Expert Reply:

Even on manufactured trailers wiring colors can vary so there is no way to say for sure. The only way to know which wire is tied to which function is to trace the wire back. On an SAE standard 7-way the brown wire would be the tail/running lights. On an RV standard it would be the right turn/brake light. Since it is a homemade trailer it could be anything. I recommend tracing the other wires back, not just the brown wire, to see what they are connected to just to make sure you wire it correctly.

expert reply by: Robin H

0

Answer 1

The brake wire providing voltage is wired in parallel, with one lead from each magnet being grounded to the trailer frame. We have a great Wiring Help Page that shows a diagram, I will provide a link to it below.

view full answer...

Answer 2

You should be getting 12 volts on the running light circuit when the running lights are turned on. If not, the problem is either in the connector or upstream from there. The first thing you should check is the trailer connector on your towing…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Function of Brown Wire on 7-Way on Homemade Flatbed Trailer

Featured Help Information

Miscellaneous Media

Continue Researching