Option For Replacement Pins For TorkLift GlowStep TLA7836

Question

Question:

The Torklift TLA7836 has 2 removeable pins that secure the steps to the black bracket. The pins are approx. 1 1/4 x 1/4. Are those pins available for sale?

asked by: Glenn M

0

Expert Reply:

Hey Glenn, we do have a potential option for a replacement pin. The pins that come with the TorkLift GlowStep # TLA7836 are not available individually, so I am afraid we cannot offer a direct replacement. What we do have is the Pin Lock for TorkLift GlowStep Scissor Steps # TLA7509, which can be used to replace the pins that hold the step to the bracket (see picture below).

The # LP14 that you were looking at appears to be the right size pin. The problem is there is no clip on the other end so there would be nothing to stop the pin from backing out. If not for that it would likely work fine as a replacement. Since no direct replacement is available though, the pin lock # TLA7509 will be our best option. Plus, you get the added security of the lock.

expert reply by: Jesse M

0

Tokrlift Pin Lock For Holding GlowStep To Bracket
(click to enlarge)

Answer 1

Hey Patrick! The Brophy Camper Scissor Steps #AS25 have the most steps with 5 steps. How long do you need them to be? At the full 48" height the steps will stick out 46" from the mounting bracket. These are designed for a 40"–48"…

view full answer...

Answer 2

We can set you up with new steps so that you love your whole camper setup, steps included. Based on the information you provided, I recommend taking a look at the Brophy Camper Scissor Steps #AS25. This is a 5-step assembly that can expand to between…

view full answer...

Answer 3

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 4

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

That’s a great question Chadwick, and this is one of those situations where the change in technology really matters. The GE Appliances Low-Profile RV AC w/ Heat Pump part #GE26RR will replace your current ARC13AACBL2 setup, but it’s important to know…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 10

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 11

The Brophy Scissor Step Bracket #TSSB will install on the edge of your tailgate. You will have to drill two holes for the L shaped pins. After drilling, all you have to do is simply insert the L pins into those holes and attach you Brophy steps! For…

view full answer...

Answer 12

Hey Doug. So long as your Husky 5th wheel hitch isn't three decades old you shouldn't have any issues attaching it to the B&W Custom Installation Kit w/ Base Rails item #BWRVK2402. Most 5th wheel hitches for the last 20 years have used…

view full answer...

Option For Replacement Pins For TorkLift GlowStep TLA7836

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching