Tongue Weight Capacity of Trailer Valet MV PRO Trailer Dolly

Question

Question:

How much tongue weight will this unit handle?

asked by: Larry D

0

Expert Reply:

Good question Larry, and the Trailer Valet MV PRO Trailer Dolly # TV96FR can handle a lot of tongue weight - 1,200 lbs to be exact. That's going to be enough for the large majority of trailers out there.

expert reply by: Kyle S

0

Answer 1

Hey Ned, the Trailer Valet RVR12 Remote-Controlled Trailer Dolly item #TV59FR has a 5 degree slope limit on a paved concrete surface. The best option I have is going to be the Trailer Valet XL Trailer Dolly with Chain Drive item #TV96FR. The Valet XL…

view full answer...

Answer 2

I'd be happy to help you find the right weight distribution hitch for your Outdoor RV 29RX Toy Hauler, but you have to measure your loaded tongue weight with your toy in the garage. The reason for this is without the weight of a toy in the garage…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Tongue Weight Capacity of Trailer Valet MV PRO Trailer Dolly

Product Page this Question was Asked From

Continue Researching