What Country Are The ARK Drop Down Corner Steadies Made In?

Question

Question:

What is the Country of origin for the ARK87FR

asked by: Darryn M

0

Expert Reply:

The Ark XO Drop Down Corner RV Stabilizer Jacks # ARK87FR, along with all of the ARK brand products, are made in Australia.

expert reply by: Jesse M

0

Answer 1

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 2

Hey Robert. Our highest capacity scissor jacks are going to be the etrailer Scissor Stabilizer Jacks. They come in a 4-pack item #e74RV or a 2-pack item #e96VV and have a 7,500 lbs capacity per jack. We do have ones rated for 10,000 lbs apiece. What…

view full answer...

Answer 3

Hey Michael, for your 2008 Forest River Salem LE 26TBSS you can use the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System #LC672136. This is a fully electric system that will work with trailer that have a GVWR up to 10,000…

view full answer...

Answer 4

Leaf springs are indeed supposed to flex and will flatten out some when under load. This reduces the distance from the top of the axle to the underside of the trailer above it. There isn't a specific distance this has to be but if the trailer is…

view full answer...

Answer 5

We usually tell people to look for about 3 inches of clearance to account for the total travel capabilities of trailer suspension. If you have less than 3 inches you might be able to compensate by using slightly longer shackle straps. I have included…

view full answer...

Answer 6

Hey Kevin! the Ark XO Drop Down Corner #ARK87FR has a support capacity of 1,925 lbs per jack. For some reason a capacity made its way onto the Ark Drop Down Corner Steadies #ARK34FR page and others like it which will need to be corrected. However,…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

What Country Are The ARK Drop Down Corner Steadies Made In?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching