Replacement Base For Converting B&W Companion To Fit The Puck System in a 2024 Ram 3500

Question

Question:

Is there a way to adapt my B&W companion form the center post mount to the factory mounts in my 2024 Ram 3500?

asked by: Shaun

0

Expert Reply:

To convert your B&W Companion # BWRVK3500 to fit the factory pucks in your 2024 Ram 3500 you will need to change the Base # BWRVB3600. Typically I recommend just getting the new Hitch # BWRVK3600 since it would be easier to sell your old Companion than to find someone who would only take the base.

expert reply by: Bud M

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 5

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 6

Hey Ralph! The Thomas Payne RV Jackknife Sofa w/ Hinges, Hardware #TP76KR requires at least 3" of wall clearance to function properly. Are you upgrading your sofa or did the old one wear out?

view full answer...

Answer 7

Hey Katy, congrats on your new trailer. The Thomas Payne RV Jackknife Sofa w/ Hinges item #TP58KR measures 64" wide x 3" deep x 23" tall when it's completely assembled. You can add the Universal Leg Kit for Thomas Payne RV…

view full answer...

Answer 8

Hello Chris, Thanks for reaching out. I completely understand wanting to confirm this before installing, especially with tight aisles and wall clearance. When the Thomas Payne RV Jackknife Sofa #TP58KR is upright, it measures 30" deep, including…

view full answer...

Answer 9

Hey Edgar, so we have pretty similar designs to the part #TP48KR in different colors that are the same size. For darker we have #TP98KR More like a light gray #TP78KR Lighter tan #TP68KR Darker brown and leather #TP32KR

view full answer...

Answer 10

Hi Mark; according to Lippert the Thomas Payne RV Jackknife Sofa #TP86KR is a "wall hugger." This means it can sit right up against the wall in the upright position. You don't need a certain amount of space behind it.

view full answer...

Answer 11

Hey Nancy! The Thomas Payne RV Jackknife Sofa w/ Hinges #TP58KR doesn't have any legs. It is designed to sit on an existing base/legs which you can see examples of in the attached picture. I can't tell in the brochure if that is what you have…

view full answer...

Answer 12

Hey Arkadius, welcome back! Yes, the ducted version of the Chill Cube comes with a remote. However, you're going to need the complete system for a replacement. You can choose from the following based on color: -Furrion Chill Cube RV Air…

view full answer...

Replacement Base For Converting B&W Companion To Fit The Puck System in a 2024 Ram 3500

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching