Is the SmartPlug RV and Marine Power Inlet UL Listed

Question

Question:

SmartPlug RV and Marine Power Inlet - 50 Amp - Stainless Steel Item # SM79FR Is this product UL listed?

asked by: Doug H

0

Expert Reply:

The SmartPlug RV and Marine Power Inlet - 50 Amp - Stainless Steel # SM79FR is ETL listed which, to my understanding, is just a slight variation of UL listed. So while it doesn't have that exact rating, it's still safe to use and has been approved by OSHA standards for electrical use.

expert reply by: Jon G

0

Answer 1

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 2

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 3

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 4

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

First you will need to replace your factory hitch on your 2024 Ford F-350 with the TorkLift SuperHitch Magnum Trailer Hitch Receiver #TL27CR. Then you will be able to attach the Rear Tie-Downs #TLR3504 to their receiver. For the front we have the…

view full answer...

Answer 7

Hey Bob, congrats on a setting up a new camper! Out of all of those options you'll also need to consider daily driving comfort unless that camper is a permanent addition to your truck bed. Listed below are a brief breakdown of each and a…

view full answer...

Answer 8

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 9

Hi Clint, welcome back The HappiJac Original Turnbuckles for Camper Tie-Downs - Stainless Steel - Qty 4 #LC182898 are likely what you are looking for and will be a good in between option (they are actually pretty nice and should last a good long…

view full answer...

Answer 10

Hey Rod, thanks for reaching out. Yes, it will! The Curt Helux Shock-Absorbing 5th Wheel Pin Box #C83RJ will indeed work with the Demco Autoslide 5th Wheel Hitch #DM8550038. Just make sure you also use the Demco Autoslide Locking Plate for Lippert…

view full answer...

Answer 11

Hello Dennis, That is definitely something you will want to check with your setup. The B&W Continuum #BW78FR will sit about 9 inches below your trailer frame once installed, so you will want to measure from the ground to the bottom of the frame…

view full answer...

Answer 12

Hi Lance, I completely understand where you’re coming from on this. You can use your factory hitch with a 48 inch extension like part #TLE1648, so you don’t have to jump to the dual receiver setup right away since this extension is designed to work…

view full answer...

Is the SmartPlug RV and Marine Power Inlet UL Listed

Product Page this Question was Asked From

Continue Researching