What Size is The Hardware For The Yakima Load Stops # Y01161 To Fit Inside The Channel?

Question

Question:

Hey I am interested in purchasing a product you guys carry but I want to confirm a measurement before buying to see if it’ll fit my bed rack. The load stop you guys carry is the t slot nut 3/4” or less ?

asked by: Marlon B

0

Expert Reply:

The T-Slot Mounting Hardware # Y38FR for the Yakima Load Stops # Y01161 is right at 3/4" wide.

expert reply by: Bud M

0

Answer 1

The Rhino Rack Vortex Pipe Clamps for Conduit Carriers #RRSPC4 will allow you to carry a 4" conduit on your Yakima HD cross bars. The Vortex uses the same size t-slots as your Yakima HD bars. The Conduit Clamp Set #RRBC2 uses M8 Channel Nuts…

view full answer...

Answer 2

The Replacement Mounting Hardware for Recovery Tracks for Yakima Ladder Racks part #Y83FR are M8 x 18mm.

view full answer...

Answer 3

We do offer replacement nut plates in a hardware bag, part #Y83FR. Yakima doesn't offer the nut plates separately.

view full answer...

Answer 4

Hey Steve, I attached a photo of the measurements I took of the main piece in this kit #Y83FR. It is going to be 31.6mm x 19.9mm. If there is a specific measurement you are looking for let me know, otherwise this is the replacement hardware for…

view full answer...

Answer 5

Yes, the Load Stops for Yakima HD Bar, JetStream, FlushBar, and RailBar Crossbars #Y01161 you're referring to will work with Thule Edge Crossbars like the Thule WingBar Edge Crossbars #TH69FE with the Edge Raised Rail Feet for Thule Edge…

view full answer...

Answer 6

In speaking to Yakima the only knob we currently carry that will fit your TopShelf #Y94VR is in the Kit #Y38FR. This kit contains 4 knobs along with other various hardware.

view full answer...

Answer 7

Hey Dave, For Rhino-Rack HD crossbars you would need the Replacement M8 Channel Nut for Rhino-Rack Accessories #RR59TB. From there you would just the appropriate length M8 bolt to mount your accessory to the channel nut.

view full answer...

Answer 8

I spoke with Yakima about the Yakima LockNLoad Platform Rack like part #Y05047-39 and they informed me that Rhino-Rack Pioneer Rack Accessories should work but this is not something they can test. I have attached a list of these accessories for you…

view full answer...

Answer 9

I am not sure why we don't carry it but the current nut plate you need is the 8881121 which you can get from Yakima.

view full answer...

Answer 10

Hey Chris, thanks for reaching out! The Yakima 54" Tracks for Roof Racks #Y26RR are designed to work with RailRider 1 Towers or Landing Pad 1 with SkyLine or Control Towers, so they aren't compatible with the Mounting Hardware #Y83FR, but…

view full answer...

Answer 11

The Replacement Mounting Hardware for Recovery Tracks for Yakima Ladder Racks part #Y83FR uses M8 hardware per Yakima.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

What Size is The Hardware For The Yakima Load Stops # Y01161 To Fit Inside The Channel?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching