Will The BAKFlip MX4 Allow For Enough 5th Wheel Hitch Clearance When Folded

Question

Question:

When folded into its all the way open but FLAT configurationnot tilted up against back window how far does it extend into the bed from front to back? Need to know if it’ll fold up and still have room for my 5th wheel hitch that dips into the bed.

asked by: Rob T

0

Expert Reply:

I reached out to the manufacturer and they stated that the BAKFlip MX4 Hard Tonneau Cover # BAK448130, when folded to the last panel, would stick out into the bed approximately 22".

expert reply by: Kevin C

0

Answer 1

A slider hitch isn't needed with an 8 foot bed truck, but it doesn't hurt anything to use one though. Only downside is that it's going to weigh more than a stationary hitch really.

view full answer...

Answer 2

The BAKFlip MX4 Hard Folding Tonneau cover that fits your 2018 Ram 2500 with 6-1/2 foot bed (and without the Rambox) is part #BAK48203. This is similar to the cover #BAK48311 that you referenced but that one is for long bed Ford pickups. The MX4…

view full answer...

Answer 3

No, use of the Timbren suspension enhancements like the Timbren Rear Suspension Enhancement System #TDRTT1500 will not void your warranty. You are protected by the Federal Magnuson-Moss Warranty Act. This act says if something breaks on your vehicle…

view full answer...

Answer 4

The Gen-Y Hitch 5th Wheel to Gooseneck Pin Box item #GY98GR weighs a hefty 120 lbs. This is the only way to add a gooseneck pin box to a 5th wheel trailer with a Rhino Box. You will also need the Safety Chain with 2 Hooks item #GY49GR. State laws…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Will The BAKFlip MX4 Allow For Enough 5th Wheel Hitch Clearance When Folded

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching