Van Lock Upgrade Recommendation for Full-Time RV Living

Question

Question:

Hi, I'm in the process of converting my van into a full-time RV. Since I'll have my possessions in the van every day I'd like to upgrade the locks if that's possible. Do you have any suggestions?

asked by: Mike W

0

Expert Reply:

We do!

I recommend checking out the Thule Van Locks # TH309833 which install on the outside of your doors. These locks require a key to unlock, but then they lock in place with a push-button feature so it's quick and easy to secure the locks in place.

Since these install on the outside of the vehicle be sure one of your doors is still able to give you a safe exit in case of an emergency.

expert reply by: Jon G

0

Answer 1

For RV applications the SumoSprings tend to be the better choice as they are less harsh than the Timbrens. Because of that I would recommend the part #SSR-313-40 which is a confirmed fit for your 2017 Ram ProMaster 3500 chassis. This is the lightest…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The hitch bolt included in the Yakima Replacement Mounting Hardware for SwingDaddy Hitch Mounted Carrier #Y8890185 measures exactly 4.28 inches long with a 1/2 inch diameter and 13 pitch. If you only need the bolt and clip you can use part…

view full answer...

Answer 4

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.

view full answer...

Answer 5

I spoke with my contact in the Tech Services department at Yakima, who tells me that the #Y8890174 adapter you mentioned is not compatible with the BigHorn 4 Bike rack you have. Instead of going with the adapter, you would need to replace the…

view full answer...

Answer 6

The bolt that comes with the Replacement Hitch Hardware for Yakima HoldUp Bike Racks #8890260 has 5/8" diameter threads with the coarse (5/8" - 11) thread spacing so it will work for your application.

view full answer...

Answer 7

While every situation is different those are the color and size wires that GM uses to wire their brake controller connections. Using these to install your Prodigy P3 part #90195 will likely result in a successful installation. That hinged on them…

view full answer...

Answer 8

In regards to installing the Redarc Tow-Pro Elite Trailer Brake Controller part #RED44FR on a 2019 Chevrolet Express Van, you'll need the Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers part #5506. There should be a blue…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Van Lock Upgrade Recommendation for Full-Time RV Living

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching