Hitch Pin and Anti-Rattle Recommendations for Curt Heavy Duty Forged Ball Mount for 2-1/2" Hitch

Question

Question:

What pin and rattle parts do you recommend for this Curtis heavy dty ball mount?

asked by: Tom M

0

Expert Reply:

To secure your Curt Heavy Duty Forged Ball Mount for 2-1/2" Hitch # C93JR to the hitch receiver I recommend using both the etrailer Hitch Receiver Lock # e98881 along with the Roadmaster Quiet Hitch # RM-062.

The locking hitch pin helps deter theft of the ball mount while the Quiet Hitch acts as an anti-rattle device and keeps the ball mount from moving inside the receiver itself.

I've attached a few review videos for you to check out!

expert reply by: Jon G

0

Answer 1

For 2-1/2 inch hitches we have the hitch lock part #e98881 which is going to be a great option for you. It has a usable span of 3-5/8 inches which would easily fit your hitch and ball mount. This has a 5/8 inch diameter which is the correct size for…

view full answer...

Answer 2

Hey JD, The Weigh Safe Hitch w/ Built-In Scale for 2.5" Hitch #WS88RR uses hitch pic lock #WS54CR, which has a shear strength capacity of 45,000lbs according to Weigh Safe.

view full answer...

Answer 3

We definitely have a lock and an anti-rattle device for your Blue Ox Adjustable 2-Ball Mount - 2-1/2" Hitch #BLU85XR but since this has a solid shank we will need to use 2 pieces as opposed to a part that has them integrated together. I…

view full answer...

Answer 4

Yes, there is. It is the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit item #BWGNRK1320. This hitch has been recently confirmed to fit the 2025 Ram 2500s. There was some concern about the exhaust being changed from…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hi Cory, can you tell me the specific part numbers and which measurements you want exactly? I only see that you looked at some Trimax HD ball mounts, and I want to make sure I'm getting all of the measurements you're looking for and on the…

view full answer...

Answer 7

Hey Dan, all of the install hardware that comes with TowSmart hitch #TS89ZR should be torqued to 86 ft lbs.

view full answer...

Answer 8

Hey Dave, thanks for reaching out. We have just the thing! To add a 7-way to the bed of your 2026 Ford F-250, you will need the following: - Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector for Aluminum Beds - 10' Long #C57010

view full answer...

Answer 9

Hey Ken! Instead of worrying about fitment and a potential return I can give you some measurements so you can figure it out before ordering. The standard shank on the B&W Continuum Weight Distribution System #BW28FR is 11-3/8" from the…

view full answer...

Answer 10

Hey Justin, thanks for reaching out! I went out to the warehouse and confirmed that the Curt Adjustable 2-Ball Mount #C79NR measures 12-1/4" from the center of the hitch pin hole to the center of the hitch ball. Not sure what tape measure Curt…

view full answer...

Answer 11

To determine if there are compatible hubs and associated bearings to replace your current hubs to a more standard size you will have to take several precise measurements on the spindle of your axle. It is recommended to use a set of dial calipers to…

view full answer...

Answer 12

Hey Jack! One of the easiest controllers to install, especially for an RV, is the Redarc Tow-Pro Liberty. The only thing visible on your dash is going to be the control knob. If the 7-way was a factory plug then you want to get part #RED96CR. It…

view full answer...

Hitch Pin and Anti-Rattle Recommendations for Curt Heavy Duty Forged Ball Mount for 2-1/2" Hitch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching