Replacement Power Supply for Thomas Payne Seismic and Momentum Series Sofas

Question

Question:

I HAVE A THOMAS PAYANE GRAND DESIGN RECLINING SOFA #7787114 I NEED A POWER SUPPLY FOR IT .DO YOU HAVE ONE THANKS

asked by: Frank B

0

Expert Reply:

I wasn't able to find anything with that part number, but if you have a Seismic series sofa, then you'd want the Replacement Power Cord with Power Supply Box for Thomas Payne Seismic RV Power Reclining Sofas # 195-000111, but if you have a Momentum series sofa then you'd want the Replacement 12V Cord for Thomas Payne Momentum Recliners and Sofas # 195-387595.

expert reply by: Bryce D

0

Answer 1

Hi Katrina! Good question. It's so good that I actually went out to our warehouse to check the specs printed on the 12V Cord #195-387595 and then did some math on top of that! The Replacement Cord is going to draw between 150 and 360 watts, while…

view full answer...

Answer 2

The recliners run off of 110V AC, using a standard 110V outlet. So, if your camper doesn't already have a power inverter you could use one like the Go Power #34280176. If your loveseat is a Thomas Payne model, you can use the #195-387595…

view full answer...

Answer 3

To replace the electrical cords for the Thomas Payne Seismic Dual Power Reclining RV Loveseat w/ Heat, Massage and LEDs, you will want to use the Replacement Power Cord #195-000111.

view full answer...

Answer 4

It sounds like you've got a Thomas Payne Seismic Dual Power Reclining RV Loveseat w Console, Heat, Massage, LEDs like the #195-091-092-090, and you need the power plug for it. In this case you'll want to use the Replacement Power Cord with…

view full answer...

Answer 5

Behind the Thomas Payne Seismic Recliners there are power connections on either end. These are located near the edges of the recliners near the bottom (see attached photo "C" connections). You'll simply push the Replacement Power Cord…

view full answer...

Answer 6

I took a look at how you can power your Thomas Payne Seismic Recliners, using the: -Replacement Power Cord with Power Supply Box for Thomas Payne Seismic RV Power Reclining Sofas #195-000111, you will need to plug one end of the power cord into a…

view full answer...

Answer 7

You will only need one Replacement Power Cord with Power Supply Box for Thomas Payne Seismic RV Power Reclining Sofas #195-000111 for your sofa as both sides are connected electrically during assembly.

view full answer...

Answer 8

The Replacement Power Control Box for Thomas Payne Seismic Recliners and Sofas #LC36FR is the correct part for your Thomas Payne Seismic Series Recliner. If you have not already, preform a hard reset on your chair before continuing. To do this unplug…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Replacement Power Supply for Thomas Payne Seismic and Momentum Series Sofas

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching