Inner Dimensions of Buyers Products Trailer Tongue Toolbox

Question

Question:

The dimensions given, are those exterior dims or interior dims? I’m trying to find a way to contain my portable generator for travel/security. The interior dimensions are the most critical factor for me in deciding on this one. Thank you

asked by: Wade

1

Helpful Expert Reply:

I reached out to the manufacturer, Buyers Products, who said the inner dimensions were 33" x 19" x 15" for the Buyers Products Trailer Tongue Toolbox - Black # 3371701680.

This toolbox is also available in White at part # 3371701679.

expert reply by: Kyle S

1

Answer 1

The Buyers Products Trailer Tongue Toolbox part #3371701680 does not come with mounting hardware. It can be secured in a number of different ways, most drill directly though the bottom of the box and into the frame. If you can find a way to mount the…

view full answer...

Answer 2

The Trimax Trailer Wheel Chock and Lock #TMX75FR and #TMX62ZR that we currently offer only come keyed unique with no way to choose the key code.

view full answer...

Answer 3

The typical requirement for a wheel chock is that it's 1/4 of the total diameter of the wheel it's being used on. A 245/45R18 tire has an overall diameter of 26.7 inches so you would need a wheel chock that's at least roughly 6-1/2"…

view full answer...

Answer 4

You could potentially mount a trailer tongue toolbox like the White Buyers Products #3371701679 to a pole tongue like what's on your Lees-ure Lite Camper but it's going to require some custom/fabricated brackets. You would need to first come…

view full answer...

Answer 5

The TruRyde Spindle #TRU94FR that you referenced has a 1-1/4-inch diameter stub. This spindle will fit an axle beam (pipe) with a 1-1/4-inch inner diameter. While you can certainly fabricate your own axle to go on your homemade trailer, assuming you…

view full answer...

Answer 6

Hi Mark; the only jack like that is the Lippert Power Stance Electric Trailer Jack #LC89VR but it exceeds the amount you're looking to spend. If you're fine with one that only runs off of the 7-way then I recommend the etrailer Electric…

view full answer...

Answer 7

Good question! The etrailer trailer tool box #e44VV is made over seas, but I do have a couple made in America options listed below. They are fairly similar and I think they might be of interest to you, since the name you entered is Usaforme. DeeZee…

view full answer...

Answer 8

Hey Tracy, thanks for reaching out! For an Anderson connector that can be hooked up to the battery on your 2022 Frontier, I recommend picking up the Bulldog Winch Rear Wiring Kit #BDW20026 which comes with 24' of 3 Gauge wire and 2 Anderson-type…

view full answer...

Answer 9

Hey Michael. The Performance Tool LED Safety Flare Set item #PT54PJ are powered by three AAA batteries each. What kind of vehicle do you have?

view full answer...

Answer 10

The safety chains you choose need to be able to handle at least 12,000 lbs so the #337B03835SC wouldn't work for your trailer. You also need to choose a length that allows you to cross the chains and also be able to make sharp turns. The best way…

view full answer...

Answer 11

Since you have wooden floors in your trailer the hardware I would recommend for installing e-track like the part #EM19147 would be the Erickson Hardware kit part #SL49FR which is basically wood screws.

view full answer...

Answer 12

Hey Yussel, congrats on the new hobby. To replace the bearings on your 2020 Apex Nano 213RDS you'll need the inner bearing item #L68149 and the outer bearing item #L44649. The inner one is bigger so it will be closest to the trailer on the inside…

view full answer...

Inner Dimensions of Buyers Products Trailer Tongue Toolbox

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching