Trailer Hitch Receiver Fit For 2024 Hyundai Ioniq 5

Question

Question:

is there a hitch that fits the 2024 hyundai Ioniq 5?

asked by: Johnny

0

Expert Reply:

There is indeed a trailer hitch receiver that fits your 2024 Hyundai Ioniq 5, from Curt. I verified this fit directly with the manufacturer for you, with the correct part number being the following:

- Curt Trailer Hitch Receiver # C98DR

Additionally, if you need a 4-way wiring harness the correct part for your '24 Ioniq 5 is the T-Connector Vehicle Wiring Harness # C59NR.

expert reply by: Kyle S

0

Answer 1

Thanks for the photo that was exactly what was needed to identify the correct Hopkins pin. Based on that, you have a Hopkins LED breakaway switch and we do have the exact replacement: - Replacement Cable and Pin for Hopkins LED Breakaway Switches…

view full answer...

Answer 2

The 2007 Jeep Grand Cherokee does not have the pre-wired port used for installation of a brake controller. To install a brake controller on your 2007 Jeep Grand Cherokee with a factory 7-Way you will need to do some hard wiring. The wire Jeep…

view full answer...

Answer 3

Just a portion of the bumper panel under your 2024 Hyundai Ioniq 5 is needed to install the Curt hitch that fits, which is the following part number: - Curt Trailer Hitch Receiver #C98DR I added a cut out from the instructions which shows the amount,…

view full answer...

Answer 4

To add a hitch to your 2024 Hyundai Ioniq 5, I recommend the Curt item #C98DR. This hitch is custom fit and bolts to your Hyundai with included hardware. This is a class III hitch with a 2" receiver. It has a 2,500 lbs towing capacity and a 200…

view full answer...

Answer 5

Hey Bruce, since the Draw Tite hitch part #DT27YR fits right up under the rear bumper you'd lose right at 2.5 inches of rear ground clearance like you see in the attached picture.

view full answer...

Answer 6

Hi Robert; I have attached the installation instructions for the Draw-Tite Max-Frame Trailer Hitch Receiver #DT27YR below. If you plan on towing you will also need the Curt #C59NR for wiring and a ball mount like the etrailer #e67DR

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Trailer Hitch Receiver Fit For 2024 Hyundai Ioniq 5

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching