Determining If The Fulton Fold-Away Coupler Hinge Will Work With Your Boat Trailer
Question:
Im considering Fulton Fold Away 3x4 to give me some clearance for my trailer tongue. I have 9 clearance on the section to install the coupler on. Trailer is model PTS26T-14. I have a photo I can send if necessary. Thanks,
asked by: Tom H
Expert Reply:
The closer to the coupler you are with the Fulton Fold-Away Coupler Hinge # FHDPB340301 better it can handle the tongue weight of the trailer, but you'll get less clearance with the tongue/coupler in your garage. There are a few other things to check before starting the installation. You'll need to measure the tongue and ensure that it's 3" wide by 4" tall and that the wall thickness is between 0.188" and 0.120" thick.
Once you've confirmed this you can then choose the placement of the coupler hinge on your trailer tongue where you have space, while still keeping in mind the pivot length requirements listed on the chart below. With this change you'll also need to make sure that your hard brake line ends before the hinge and transitions into a soft line to be able to accommodate the bend.
I've attached a short video below where Conner will walk you through the installation process.
(click to enlarge)
Product Page this Question was Asked From
Fulton Fold-Away Coupler Hinge Kit for 3" x 4" Tongue - Bolt On - Up to 7,000 lbs
- Folding Trailer Tongue
- Coupler Hinge Kit
- Up to 48 Inch Long
- Bolt-On
- 7000 lbs GTW
- 3 x 4 Inch Tongue
- Fulton
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Converting Trailer from Surge Brakes to Electric Brakes
- Shop: Hopkins Engager Trailer Breakaway Kit w/ Charger, LED Tester, Hardware, and 5 Ah Battery - Top Load
- Shop: Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs
- Search Results: primary wire
- Q&A: How to Wire Electric Brakes on a Tandem Axle Trailer
- Q&A: Wiring Needed For Electric Trailer Brakes On a 7,000LB Car Hauler Trailer
- Search Results: trailer tires and wheels
- Q&A: How to Convert a Trailer with Surge Brakes to Electric Over Hydraulic Brakes
- Q&A: Replacement Solution for Fulton Swing Away A60 Drum Brake Actuator
- Shop: Dexter Electric Trailer Brake Assembly - 10" - Right Hand - 3,500 lbs
- Shop: 12 Gauge 2 Conductor Jacketed (Brake) Wire Per Foot
- Shop: Wiring Kit for Hydrastar Electric Over Hydraulic Actuators
- Shop: 12 Gauge Wire - Black Primary - Per Foot
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Search Results: spare tire mount
- Search Results: trailer steps
- Search Results: trailer breakaway kit
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer jack
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Trailer Wiring
- Shop: RV Bearing
- Video: Finding the Right Trailer Wiring Harness
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: etrailer VS Dexter Self Adjusting Brakes Comparison
- Q&A: What Gauge Wire Should be Used to Wire Trailer Brakes
- Shop: Brake Controller
on Folding Trailer Tongue
