Will The 8" Wide Carpeting Fit Around a 2" X 6" Bunk Board?

Question

Question:

Will the product FCR8008 material wrap around a 2inch x 6inch board enough to put staples in it.

asked by: Kevin L

0

Expert Reply:

I recommend using at least 11" Wide Carpeting # CE11330 for a 2"x6" bunk board. The 8" # FCR8008 would require you to place the staples on the edge of the bunk board where they are more likely to pull through the carpeting.

expert reply by: Bud M

0

Carpeting Diagram
(click to enlarge)

Answer 1

Bunk Carpet like the part #FCR8008 you mention is typically stapled or glued into place. If you decide on using staples, make sure you shoot the staples into the underside of the bunk board so that the boat will not be scratched. A combination of…

view full answer...

Answer 2

From my research, it seems that a combination stapling the carpet to the bunks using stainless or Monel (primarily an alloy of copper and nickel) staples and outdoor carpet adhesive is the preferred method of attaching carpet. I replaced the bunks on…

view full answer...

Answer 3

The only color bunk carpet that we have is the dark gray/black that you see in the pictures for #FCR8008 or #FCR8012. The difference between these two items is that the first is 8 inches wide and the second is 12 inches wide. Both are 144 inches…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Will The 8" Wide Carpeting Fit Around a 2" X 6" Bunk Board?

Products Featured in This Question

Continue Researching