Recommended Brake Controller for a 2008 Chevy Tahoe

Question

Question:

Hey I’m looking for a brake controller for my 08 Tahoe ltz. I’ll be towing a 5200lb pull behind camper. I’d like a controller and the correct wiring harness for plug and play. Thanks

asked by: Wesley

0

Expert Reply:

I have a great brake controller for your 2008 Chevy Tahoe but GM did not install the necessary port for a plug and play harness in your SUV so you will have to hardwire one in.

The best option brake controller for your 2008 Chevy Tahoe LTZ is going to be the Redarc Tow-Pro Liberty Brake Controller item # RED24FR. This is a proportional brake controller that activates your trailer's brakes when your Tahoe decelerates.

The reason the Tow-Pro Liberty is the best option is because of its unique installation method where the only visible portion is the control knob that's about the size of a nickel. The main unit is hidden away inside your dash to be completely out of the way and out of sight.

You will need the Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item # RED69FR to complete the installation, since your Tahoe does not a brake controller port installed from the factory.

If you are adamantly against cutting and splicing wires the only other option I have for you is the Curt Echo Wireless Brake Controller item # C51180 which plugs directly into your 7-way connector and is controlled by an app on your phone.

expert reply by: Jerred H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Recommended Brake Controller for a 2008 Chevy Tahoe

Products Featured in This Question

Continue Researching