Replacement Knob, Shaft and Screw for a MaxxAir MaxxFan and MaxxFan Deluxe

Question

Question:

I find the shaft that i need, MA10-21232KSHAFT, but i also need the knob and the knob screw. I dont find those. Can you point me to the part number?

asked by: Jim S

0

Expert Reply:

Yes, I can help you out with that!

The correct knob and screw to go with the Replacement Locking Knob Shaft for MaxxAir MaxxFan RV Roof Vents # MA10-21232KSHAFT is the Replacement Locking Knob Screw # MA10-21241K and Replacement Dome Control Locking Knob # MA74RR.

expert reply by: Scott S

0

Answer 1

The two most likely causes of a MaxxAir vent fan lid not opening or closing are either going to be a lift motor or operator failure. I recommend removing the motor and applying power directly to this to see if the shaft turns. If not, you know the…

view full answer...

Answer 2

Yes, we have exactly what you are needing! I spoke with my contact at MaxxAir who said that the replacement screw for the lid adjustment knob on your MaxxFan Roof Vent #MA00A04301K is part #MA10-21241K. It is 2.75 inches long with 0.75 inches of that…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Replacement Knob, Shaft and Screw for a MaxxAir MaxxFan and MaxxFan Deluxe

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching