Solution for Needing to Adapt 4-Way Round to 7-Way
Updated 05/16/2024 | Published 08/07/2023
Products Featured in This Question
Question:
I bought item#337TL257M, i need an adapter to go from the 4 pin round connector to a 7 blade connector on the back of my motorhome ?? Thank You,
asked by: Tim K
1
Helpful Expert Reply:
Since there isn't an adapter available to convert the 4-way to a 7-way your best option would be to cut off the 4-way and wire it to a 7-way connector like part # A7WCB. This way your trailer will not require an adapter and everything would work.
expert reply by:
Jameson C
1
Product Page this Question was Asked From
Heavy-Duty Magnetic Tow Light Set - Red Incandescent - 30' Harness with 4-Pin Round Plug
- Flat Tow Wiring Harness
- Bypasses Vehicle Wiring
- Removable Tail Light Kit
- Universal Fit
- 4 Round
- Buyers Products
more information >
Continue Researching
- Shop: Trailer Wiring
- Shop: Softride Hang2 Vertical Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Tilting
- Shop: 7-Way Round RV Style Trailer Connector - Trailer Side
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: 4 round to 7 blade adapter
- Search Results: 7 way round to 4 way round connector
- Shop: Vehicle Tow Bar Wiring
- Q&A: Installation of the Curt Wiring Harness C59236 on my 2011 BMW X5
- Search Results: 20 foot long harness flat tow wiring harness
- Search Results: wire protection
- Video: A Closer Look at the Heavy Duty Magnetic Tow Light Set
- Video: A Closer Look at the Curt Trailer Connector Adapter
- Search Results: 7 way to 4 way adapter
- Search Results: wiring protection wiring
- Shop: Universal Magnetic Tow Lights - Red LEDs - 20' Wiring Harness with 4-Way Flat Trailer Connector
- Shop: Heavy-Duty Magnetic Tow Light Set - Red Incandescent - 30' Harness with 4-Pin Round Plug
- Shop: Curt Trailer Connector Adapter - 7-Way RV Style to 4-Way Flat - 60" Cord
- Shop: Universal Magnetic Tow Lights - 20' Wiring Harness with 4-Way Flat Trailer Connector
- Q&A: 4-Way to 7-Way/4-Way Adapter that Has Both Connectors Active at Same Time
- Q&A: How to Power Blue Ox Patriot Braking System When Vehicles Negative Battery Cable Is Unhooked
- Q&A: Is Vevor RN-QVR 7500 Tow Bar Compatible With Blue Ox Base Plates
- Q&A: Recommended SumoSprings for a Tandem Axle Trailer w/ 7,000 lbs Underslung Axles
- Q&A: Complete Setup for Flat Towing 2026 Chevrolet Colorado
- Article: How to Choose a High-Low Adapter
- Article: Roadmaster Vehicle Specific Base Plates
- Q&A: Recommended Flat Towing Wiring Harness for a 2025 Ford Ranger Raptor
- Article: Can You Flat Tow a 2025 Cadillac Escalade?
- Article: Must-Have Flat Towing Components
- Article: Flat Towing Package for 2007-2018 JK Jeep Wrangler and Wrangler Unlimited
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)
David
5/16/2024
Good afternoon Jameson, A couple of months ago you helped me with some upgrades for both my trusty old 1991 YJ and some upgrades for my RV. The one product that I think I failed to order (I haven't completed all the miscellaneous upgrade/replacements yet so it still might be in a box somewhere) is the brake-light/turn signal wiring kit for my '91 YJ so I can flat-tow it behind my RV. My RV has the round 6-pin receiver and you had recommended a wiring harness kit so the YJs brake lights and turn signals would sync-up with the RV. Remind me.....which kit was that ?! Also, I wonder if this magnetic kit (337TL257M) would be the simplest approach? But then I would need to do some wiring/splicing to discard the 4 plug connector that is built-in to this magnetic set and re-wire and re-place a new round 6 pin connector in place of the 4 pin connector the kit come with. Although I'm a slightly above average handyman kinda' guy, wiring/splicing is not my strong suit. How difficult would it be to cut of the 4 pin and replace it with the 6-pin. How would I know which wires go where for the conversion? Is (A7WCP) that part? David Hollis