Solution for TDE LP7000 Actuator with Leaking Master Cylinder

Question

Question:

Hello, My master cylinder is leaking, and I would like some advice on what part to buy.

asked by: Ben K

0

Expert Reply:

What you have is a TDE LP7000 actuator which we do not have replacement parts for. If you can find one elsewhere that would be simplest solution. Otherwise we could help with a replacement actuator.

Drum Brakes: Dexter DX7.5 Drop-N-Go Brake Actuator - Drum Brakes # 099-175-00

Disc Brakes: Dexter DX7.5 Drop-N-Go Brake Actuator - Disc Brakes # 099-175-20

expert reply by: Jameson C

0

Answer 1

Hey Stephen, this is a great question but I don't have a great answer. Both of our part numbers #DX69FR and #DX43FR represent the same exact Dexter DX7.5L A-60XL Surge Brake Actuator. I am not sure why we have two part numbers for the same thing…

view full answer...

Answer 2

I'm guessing it is approximately 3-3/8" across if you measured it. Unfortunately there are no options that will slide in because it won't line up correctly, and everything is designed to fit a 3" tongue so it is too wide to mount an…

view full answer...

Answer 3

In terms of capability the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K #DX89FR is a good replacement option. The problem is the design of your old TDE LP7000 which was installed inside the tongue…

view full answer...

Answer 4

Hey Scott. You can send any pictures you have directly to the email address you receive this response from. We do not have any replacement parts for a TieDown Engineering LP7000 brake actuator but we do have a couple of replacement options. To…

view full answer...

Answer 5

As your 2008 Ranger Boat Trailer has a swing away tongue with the Tie Down Model 70LP brake actuator the Dexter Disc #DX73FR or Drum #DX67FR actuator is likely going to be your best option. Both of these are a weld on application so you would need to…

view full answer...

Answer 6

Hey Neil, so we can help but we don't have a rebuild kit or an exact replacement for the Tie Down model 70lp that you referenced. The Dexter Disc #DX73FR or Drum #DX67FR actuator is going to be your best option. These are weld on actuators but we…

view full answer...

Answer 7

Hey Keith do you have any part numbers off of that actuator? Also how does yours attach to your trailer's tongue? The Dexter DX7.5L A-60XL Surge Brake Actuator item #DX69FR, you were looking at is for disc brakes. This one welds to a 3" wide…

view full answer...

Answer 8

I would be happy to help! I recommend replacing your discontinued Tie Down Engineering LP7000 with the Dexter DX7.5 Drop-N-Go Brake Actuator - Disc Brakes - 2" Ball - Zinc Plated - 7,500 lbs #099-175-20 you were looking at. This actuator is…

view full answer...

Answer 9

The Dexter drop-n-go #099-175-20 would definitely have the same capability as your TDE actuator, provided it is a disc brake setup. TDE is no longer in business so I'm afraid finding a direct replacement will be impossible. My main concern is the…

view full answer...

Answer 10

To replace your TDE Model LP7000 actuator, I recommend the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout item #DX89FR. This coupler is designed to mount on top of a standard 3" wide trailer tongue. It measures right at 3-3/8" wide so…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Solution for TDE LP7000 Actuator with Leaking Master Cylinder

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching