5th Wheel Wiring Harness For 2000 Ford F-350 With Square Plug

Question

Question:

fifth wheel plug my factory plug is square the pic of your product is round 2000 ford super duty will it fit

asked by: Steve M

0

Expert Reply:

A 5th wheel wiring harness with a round plug won't fit the square plug of your 2000 Ford F-350 Super Duty but we do have one that will work for your truck. The correct harness for the square plug on your truck is the following:

- Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness with 7-Pole Plug # 40167

expert reply by: Kyle S

0

Answer 1

Yes, we have kits designed exactly for this as it's a pretty common request. What you want is the part #41157. This installs inline with the current 7-way you have and gives you a second one you can install where needed.

view full answer...

Answer 2

Your Curt #C15316 is for the deep drop bumper and has a measurement of just over 9 inches according to my contact at Curt. He said the #C15410 is 5.32 inches from the frame to the top of the crosstube and they don't have anything in between those…

view full answer...

Answer 3

Yes, you can definitely cut out parts of the BedRug Custom Full Truck Bed Liner so that you have access to the puck system for 5th wheel towing with your 2013 Ford F-350. The correct BedRug for your pickup depends on the following specs for your…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

5th Wheel Wiring Harness For 2000 Ford F-350 With Square Plug

Continue Researching