Parts Needed to Install Yakima Round Bar Roof Rack on 2015 Toyota Tacoma Access Cab

Question

Question:

looking for 1 pair Yakima Landing Pad 26 , 1 pair Yakima skyline Towers and 2 round pipe adapters. also want to know if 48 Yakima round crossover is long enough for front cab position on 2015 Tacoma access cab with Skyline Towers on landing pads

asked by: Glenn M

0

Expert Reply:

For your 2015 Toyota Tacoma Yakima has a round bar roof rack that is a confirmed fit but it uses the Baseline towers and not the Skyline towers so you would need the part # Y00409, # Y28TR, # Y03536, # Y06125, # Y06128.

This is a 58 inch bar setup and based on install pictures I've seen of this rack on a similar Tacoma a shorter 48 inch bar would not fit.

expert reply by: Jameson C

0

Answer 1

I pulled a Replacement Square Nut #853-7557 from our warehouse and found that its dimensions were .79 by .79 of an inch and .17 of an inch thick. Check out the video I took that shows these dimensions.

view full answer...

Answer 2

Yes, the older Thule Hullavator (897XT) will fit Yakima JetStream bars. You'll use the T-Slot mounting hardware that would have come with the older model carrier and then you need to make sure you can move the carrier out far enough that there is…

view full answer...

Answer 3

From my understanding you should just need the M6 x 30 Socket Head Cap Screw #TH919063054, the M6 Washer #951061254, and the Square Nut #853-7557 for installing the older Hullavator into the T-Slot of a crossbar system. This stuff should have come…

view full answer...

Answer 4

I would be happy to help you find roof racks for both your 2015 Toyota Tacoma Double Cab and your camper shell. I'll start out with the roof rack for your truck. It is the 2015 Toyota Tacoma Roof Rack by Yakima. These 60" wide heavy-duty…

view full answer...

Answer 5

The brackets on the Thule Hullavator 897 and the Thule Hullavator 897XT are not the same. The first generation Hullavator was designed to only work with Thule square bars, so it will not work with your Thule WingBar Evo. The updated model, 897XT, was…

view full answer...

Answer 6

The replacement bar mount assembly just includes the bar mount, you'd still need the mounting hardware, so you will need 8 of the Replacement Socket Head Cap Screw for Thule Fit Kits and Ski Carriers #TH919063054 and 8 of the Replacement Square…

view full answer...

Answer 7

To get replacement T-Slot hardware for your older model 897XT Thule Hullavator carriers you need the following parts (4 per Hullavator system): - Square Nut #853-7557 - M6 x 30 Socket Head Cap Screw #TH919063054 - M6 Washer #951061254 I've…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

There are a couple of differences between the two. The JetStream bars like #Y00425 are made of extruded aluminum while the CoreBars such as the #Y00421 you've looked at are constructed of galvanized steel. As you've mentioned, the CoreBar has…

view full answer...

Parts Needed to Install Yakima Round Bar Roof Rack on 2015 Toyota Tacoma Access Cab

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching