How to Determine Axle Replacement For Trailer With 5 on 4-1/4 Hub Pattern & No Wheels Available

Question

Question:

I have an older trailer that I believe is 5 x 4 1/4. Do you have any wheels and tires?

asked by: Todd K

0

Expert Reply:

There are no wheels with a 5 on 4-1/4" bolt pattern available so what you'll need to do is switch out the axle to get one that has a hub with a standard, modern bolt pattern. To do this, you will need to know the dimensions of your current axle's hub face to hub face and spring center to spring center; I have added a link below to a video which walks you through how to measure. The other thing you need to know is the weight capacity of the axle you need, which should match or exceed the GVWR of your trailer.

For example, the Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern # e82GR has a 2,000 lb capacity and measures 60 inches from hub face to hub face and 48 inches from spring center to spring center.

expert reply by: Kyle S

0

Answer 1

The etrailer axle part #e82GR can only be installed in an underslung orientation. Since the axle has a bow to it if you were to flip it the alignment would be way off. You'd have to weld spring seats on the opposite side of the axle with the part…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

How to Determine Axle Replacement For Trailer With 5 on 4-1/4 Hub Pattern & No Wheels Available

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching