Which Timbrens and SumoSprings Fit the 2022 Grand Design Solitude 3540

Question

Question:

I have a 2022 grand design 3540 fifth wheel and would like to know which TIMBREN and SUMO bump stop fits it.

asked by: Larry C

0

Expert Reply:

The correct Timbrens for your 2022 Grand Design 3540 are the part # T92MR that you referenced and the correct SumoSprings are the part # SS33HR.

expert reply by: Jameson C

0

Answer 1

I recommend using the SumoSprings Trailer Helper Springs #SS26MV on your 2021 Grand Design Momentum 395M. These springs are rated for use on axles with a capacity of 5,000-8,000lbs and are mounted below the leaf springs. Your Momentum has three…

view full answer...

Answer 2

The grease fitting that is on top of the head unit on your Reese 5th Wheel Trailer Hitch, #RP30084, is used to lubricate the pivot points of the jaws. Using a lithium grease, #L11354, is acceptable. You will also want to lubricate the jaw itself, and…

view full answer...

Answer 3

Based on my research it appears the HC3Z-19D520-A part you mentioned is an OEM, slightly higher-rated version of the Reese M5 Series 5th Wheel Hitch #RP30922 that will mount directly to the factory pucks in the bed of your F-450. Before you take your…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hello Matt, I was seeing some mixed information on this as well, so I reached out directly to my contact at Firestone to confirm. The Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F44XV will fit…

view full answer...

Answer 12

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Which Timbrens and SumoSprings Fit the 2022 Grand Design Solitude 3540

Products Featured in This Question

Continue Researching