Recommended 3-3/16 Inch Rubber Wiper Seal w/ a Bulb

Question

Question:

I’m looking for an rv slide wiper seal WITH a bulb seal on it, I see you have a 4 1/16” wiper seal but no bulb seal on it. Can I make it work? Is there a way to add a bulb seal to it somehow?

asked by: Ryan M

0

Expert Reply:

We don't have a way to add a bulb seal to the Rubber Wiper Seal for RV Slide Out 4-1/16" Wide item # SR46FR you were looking at. There is a 3-3/16" Wide Rubber Wiper Seal with a Bulb it is item # SR48FR.

expert reply by: Jerred H

0

Answer 1

Hi Jerry; do you have a ductless or ducted setup? For whatever reason the Fogatti InstaCool Ultra #FG72FR is only designed to work with ductless setups, no option for ducted is available at this time. If you have a ductless setup you will need the…

view full answer...

Answer 2

Hello Mo, thanks for reaching out. According to Solera, the screws for their head covers are 6-15 UNF x 1/2”. We do not carry the screws by themselves, but if you check your local hardware store you should be able to find some thing compatible.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Recommended 3-3/16 Inch Rubber Wiper Seal w/ a Bulb

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching