Hitch Pin Hole Size For EcoHitch Trailer Hitch on 2023 Chevy Bolt EV

Question

Question:

What is the hitch pin size for this hitch? Most class II hitches seem to use 1/2inch diameter, but then again most class II arent 2inch receiver tubes. Thanks!

asked by: Mike A

0

Expert Reply:

That's a really good question, and because it is a 2 inch hitch, the hitch pin hole size is the standard 5/8" on the EcoHitch Hidden Trailer Hitch Receiver # 306-X7359.

So you can use a standard hitch pin or lock like the Hitch Pin # ML1465DAT or Hitch Lock # e98882.

expert reply by: Kyle S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 4

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 5

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 6

Hey Mayra, thanks for the information and the picture. The Replacement #921 Lamp Bulb item #VA0415-00 would indeed replace your Hengs Range Hood Model RO624500C lamp. However, I have a better option for you. I recommend the 921/906 LED Light Bulb…

view full answer...

Answer 7

We sure do Bruce and welcome back! The Curt V-5 S0700U-R2 receiver is our Ball Mount item #D-26. The Curt item #D-26 is a 2" ball mount with a 7,500 lbs towing capacity. It provides a 3/4" rise, a 2" drop, and has a 1" diameter…

view full answer...

Answer 8

Hi Raymond! I have a couple options you may be interested in, but that's quite a conundrum. I do know there are no 4 bike racks that can hold a spare tire as well as the bikes, but you may be able to use a cargo carrier, like the 24x60 etrailer…

view full answer...

Answer 9

The long and short of it is that you need to route wiring from the cold side of the stop light switch (only gets hot when brake pedal is pressed) on your dinghy up to the location that you are mounting the RoadMaster Replacement LED Display Monitor…

view full answer...

Answer 10

Hey Matt! The distance from the center of the #BLU74HR hitch ball to the center of the closest hitch pin hole is 8". The next hole is 1-1/8" back so from the ball it is 9-1/8". What trailer are you towing?

view full answer...

Answer 11

Hey Johnny, thanks for reaching out! I highly recommend using the Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor #LC196308 as a replacement for your 8532-07 motor. According to my research your motor is rated for 5,500 lbs so this motor will…

view full answer...

Answer 12

Hey Tyler, thanks for reaching out. I'm sorry to say no, we don't have a 5 on 4-1/2" hub, or any hub for that matter that fits a 3/4" straight spindle. That kind of spindle was really only seen on older trailers and is basically…

view full answer...

Hitch Pin Hole Size For EcoHitch Trailer Hitch on 2023 Chevy Bolt EV

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching