Replacement Mounting Hardware for 2011 GMC Sierra Westin Grille Guard

Question

Question:

I have a 2011 GMC 2500HD and need some replacement brackets for a Westin HDX Grille Guard. Im not 100 sure what type of grille it is but I have a identification number stamped in the side if that helps. U120206017-11

asked by: Kasey

0

Expert Reply:

For your application we have the Westin HDX Grille Guard with Punch Plate # 57-3665 as the only Westin grille guard to fit your 2011 GMC Sierra. To replace the mounting hardware for this grille guard you need the Kit # 57-366PK.

expert reply by: Jon G

0

Answer 1

In regards to replacement brush guard brackets for a 2012 GMC Sierra 2500, these are specific to the make and model of the brush guard. They are not universal and we cannot recommend using them as such. For example, if you have the Westin HDX Grille…

view full answer...

Answer 2

To install a Westin HDX grille guard on your 2012 GMC 3500 you will need the mounting kit part #57-366PK. We also have replacement rubber stripping for the uprights if that is needed part #57-0001. I have included a link to the installation…

view full answer...

Answer 3

For your 2011 GMC Sierra 2500 HD you need the Westin Sportsman Grille Guard #45-3660 as the part #40-1245 you referenced fits older 2500 and 3500 HD models. The part that fits is only offered in stainless steel at this time because the black version,…

view full answer...

Answer 4

For starters, are you sure that you have the Westin HDX Grille Guard with Punch Plate part #57-3665? There is more than one HDX Grille Guard and they look the same but are not. The HDX Grille Guard would need to be made specially for your 2012 GMC…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 7

I am sure we do but Big Tex does not have any kind of database to show what replacement parts fit their trailers. I would be happy to see if we have studs that would work for your hubs, but first I will need to know a few measurements of your current…

view full answer...

Answer 8

Unfortunately we do not have a video of the HappiJac Truck-Mounted Camper Tie-Downs #LC184089 being installed. The Rear anchors are installed in the end of the bumper. There is no precise mounting location since a variety of bumpers may be installed.…

view full answer...

Answer 9

I couldn't be 100% positive about which wheel studs you'd need without seeing the trailer and being able to measure. I just don't have enough information. This bein said, by virtue of the trailer having a 5 on 4-1/2 inch wheel bolt…

view full answer...

Answer 10

For the ST235/80R16 tire, you have a 30.79 inch outer diameter with a 9.25 inch width. Moving up to the ST235/85R16 tire, you will move to a 31.7 inch outer diameter with a 9.3 inch width. As long as you have the space for the extra 1/2 inch in your…

view full answer...

Replacement Mounting Hardware for 2011 GMC Sierra Westin Grille Guard

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching