Do Tekonsha Primus IQ and Prodigy P3 Brake Controllers Both Use the Same Plug

Question

Question:

I have a Primus IQ9160 wired into My truck. My new trailer has electric overhydraulic brakes. What are my best options? Will the ninety one ninety five plug in to the Plug that I already have.

asked by: Sam P

1

Helpful Expert Reply:

Both your Tekonsha Primus IQ TK90160 and the Prodigy P3 # 90195 have the same plug at the back so you'll easily be able to swap out the controllers.

This will be a nice upgrade since the P3 is compatible with electric over hydraulic brake systems plus it has the LCD screen and storable trailer settings.

Attached is a review video for you to check out!

expert reply by: Jon G

1

Answer 1

As you can see on the attached photo, the wiring diagram for the actuator shows there can be a 25-40 amp circuit breaker in-line with the black wiring which goes from the battery's positive terminal to power the actuator. This is actually only…

view full answer...

Answer 2

To install your Tekonsha Prodigy P2 Trailer Brake Controller #90885 on your 1999 Ford F-250 Super Duty you need the Tekonsha Plug-In Wiring Adapter #3035-P. This will connect to the factory connector on your truck. I have linked an installation video…

view full answer...

Answer 3

Yes, per the installation instructions, your 2014 Nissan Pathfinder with the Controller Area Network, or CAN Bus system, it is recommended by the manufacturer that you use the 30-amp circuit breaker kit #331-CBK30-EB. This, along with your Redarc…

view full answer...

Answer 4

The Prodigy P2 brake controller #90885 and the Primus IQ #TK90160 share some basic features, but there are many differences. The most obvious ones are the displays and appearances of the units, which are connected to the usability of the brake…

view full answer...

Answer 5

I went and pulled a Replacement Air Gauge for Air Lift Load Controller Compressor #AL25194 to grab some dimensions to help you determine if it would fit in the gauge pod you have. The portion that would fit into the pod measure 2-1/2 long if you…

view full answer...

Answer 6

Hey Joe, The easiest way to install your replacement harness is to unplug one wire at a time and replace it with your new wiring harness. With that being said, I definitely can appreciate just wanting to unplug everything and start fresh. I'm…

view full answer...

Answer 7

The gauge used with the heavy duty Air Lift compressor system, #AL25854, has 4 wires because the switch is built into the gauge. The black wire is the ground, white is the signal to the compressor, red and green are ignition power wires. I have…

view full answer...

Answer 8

It sounds like the compressor system may not be getting power or is not waking up. Depending on how the Air Lift WirelessONE Compressor System #AL25980 is wired to your vehicle you may have to do additional steps. The wiring harness has a ignition…

view full answer...

Answer 9

I checked with Air Lift and was able to find a wiring diagram for the Replacement Air Gauge for Air Lift Load Controller Compressor System #AL25194 and attached it to this page.

view full answer...

Answer 10

I've attached the wiring diagram for you to check out, but it sounds like the compressor for your #AL57289 is not getting power. The wiring harness has an ignition wire which if not connected to an ignition source, will not wake up the compressor…

view full answer...

Answer 11

Yes, since the Replacement Dual Analog Gauge for Air Lift Load Controller Compressor System #AL25195 is a replacement gauge for the #AL25852 which is a dual path setup that allows for having two different pressure settings like you are looking for.

view full answer...

Answer 12

Yes we have just the replacement gauge you are looking for with the part #AL25195.

view full answer...

Do Tekonsha Primus IQ and Prodigy P3 Brake Controllers Both Use the Same Plug

Featured Help Information

Miscellaneous Media

Continue Researching