Which SeeLevel Holding Tank System For 5th Wheel

Question

Question:

I am looking to put in the replacement holding tank sensor system. I have a a 2022 Alliance RV Paradigm 5th wheel 35 ft. Which sensor system should I get?

asked by: Don D

0

Expert Reply:

This really depends on if your 2022 Alliance Paradigm has an RV-C, multiplex wiring system which usually connects to a central control panel. If you have that, then use the SeeLeveL RV Holding Tank Monitoring System # SE99VR.

If you don't have that wiring system in your RV then go with the SeeLeveL RV Holding Tank Monitoring System # SE39VR.

expert reply by: Kyle S

0

Answer 1

Hey Jim, since the Tmat systems are designed to slide in and out you can just remove the mat when towing or you can trim/cut the Tmat to fit around the rails as needed. What year Ram 3500 do you have and how long is your truck bed? What type of hitch…

view full answer...

Answer 2

We've had this question before and the manufacturer of the ThermaHeat #277-000164 that you referenced has stated that it's okay to insulate over the heating pad.

view full answer...

Answer 3

Since the inverter would output 12 volts it would be the same running the Therma heat RV tank pad heater part #277-000164 to that as it would be a 12 volt battery.

view full answer...

Answer 4

No, the SeeLeveL RV Holding Tank Monitor #SE84VR does not include the sensors. The sensors are sold separately. - SeeLeveL Sensor for RV Holding Tank Monitor #SE78VR (12") - SeeLeveL Sensor for RV Holding Tank Monitor #SE27VR (16")

view full answer...

Answer 5

Hello Ron, thanks for reaching out. The SeeLeveL RV Holding Tank Monitoring System #SE59VR you mentioned comes with the 12" long tank sensors. If you are needing just the sensors, they are available individually as part #SE78VR.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Hey Tom, congrats on the new truck! Typically when we hear that someone has the OEM tow prep package they mean the puck system. This is going to be five circular holes built into the bed of your Ram truck and is by far the best way to attach a 5th…

view full answer...

Answer 11

Hi Glen, It's good to hear from you again! If you're wanting to switch to the Roadmaster Comfort Ride system with the leaf spring, equalizer, and shock absorber upgrades, I recommend using the Roadmaster Comfort Ride Leaf Spring Suspension…

view full answer...

Answer 12

Hey Jerry, thanks for reaching out. The short answer is yes, probably but it really depends on your exact setup. When you slide the Companion back, you gain cab clearance but lose space at the tailgate, and with a MorRyde pin box being a bit bulkier,…

view full answer...

Which SeeLevel Holding Tank System For 5th Wheel

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching