Does the SeeLeveL RV Holding Tank Monitor SE84VR Come With the Sensors

Question

Question:

Does the SE84VR model include the sensors for all four tanks?

asked by: Emil C

0

Expert Reply:

No, the SeeLeveL RV Holding Tank Monitor # SE84VR does not include the sensors. The sensors are sold separately.

- SeeLeveL Sensor for RV Holding Tank Monitor # SE78VR (12")

- SeeLeveL Sensor for RV Holding Tank Monitor # SE27VR (16")

expert reply by: Scott S

0

Answer 1

The SeeLevel systems will require you to replace your current monitor in order to properly read the sensors and operate. There are quite a few different combinations of monitors and sensor strips so I'd like to know exactly what you're…

view full answer...

Answer 2

I reached out to SeeLevel who said the SeeLeveL Sensor for RV Holding Tank Monitor #SE78VR will work on schedule 40 PVC pipe but it has to be at least 3 inches in diameter. They also said didn't specify the exact signal type but said it would not…

view full answer...

Answer 3

Yes, the SeeLeveL Sensors #SE27VR can be used on a tank mounted under a van. You'll just want to make sure that you cut the sensors to the correct length for the tank, and only cut in the specified points seen in the picture below. You'll…

view full answer...

Answer 4

The 60-Amp Relay Kit for Redarc In-Vehicle BCDC Battery Charger #331-RK1260 will easily survive use up to it's amperage rating of 60 amps. Under normal regular use there would be no need to replace the relay frequently.

view full answer...

Answer 5

Let's start with the ignition wire you were asking about for the Redarc In-Vehicle BCDC Battery Charger - Dual Input - DC to DC - 12V/24V - 25 Amp #331-BCDC1225D. What you will do is connect the blue wire from the charger directly to an ignition…

view full answer...

Answer 6

Your auxiliary power wire gauge at your 7-way along with the discontinued CTEK40186 will be sufficient to charge your trailer batteries. The CTEK D250S will amplify the signal from your auxiliary power to boost it to 20 amps versus the 2-3 amps of a…

view full answer...

Answer 7

The pin of the relay that comes with the #331-RK1260 that runs to "ignition" only needs a power source that is active when the key is on to basically tell the relay to activate. You don't have to actually splice into ignition wiring. So…

view full answer...

Answer 8

Since the estimated length of the wire run you'll have with the part #331-BCDC1240D is between 18 and 20 feet you'd want to use 4 gauge wire. If the run was less than 16 feet you could use 6 gauge. The two relay kits you mentioned actually…

view full answer...

Answer 9

We do have the SeeLeveL RV Holding Tank Monitor #SE84VR which monitors fresh, gray, black, and galley tanks. This is the closest we have to your fresh, galley, bath, and black tanks. Your bath would just be labeled gray instead of bath. This monitor…

view full answer...

Answer 10

We have the 710-AR and 710-ES2 SeeLevel sensors, though I was unable to find any 701AR or 701ES2. If you were referring to the 710-AR and 710-ES2 you would need the following: - 710-AR: SeeLeveL Sensor #SE88VR - 710-ES2: SeeLeveL Sensor #SE78VR

view full answer...

Answer 11

Easiest way to explain the wiring colors of the Hopkins harness part #HM20041 is for me to just list what the wires color functions are as follows. White: ground wire Yellow: left turn/brake light Green: right turn/brake light Brown: tail lights…

view full answer...

Answer 12

The EZ Connector Magnetic 7-Way Trailer Connectors #319-R7-01 are rated for up to 40amps of power on the 10 gauge wiring. These wires are for the charge line and ground wire circuits. The lighting and brake line wires uses smalle 12 and 14 gauge wire…

view full answer...

Does the SeeLeveL RV Holding Tank Monitor SE84VR Come With the Sensors

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching