Recommended Bearings, Brake Assembly, and Hub for a Dexter 7,000 lbs Axle

Question

Question:

Bearings, brake assembly and hub for 7000LB Dexter axle

asked by: Derek S

0

Expert Reply:

Bearings - Inner Bearing item # 25580, Outer Bearing item # 14125A, Inner Race item # 25520, Outer Race item # 14276, and Grease Seal item # GS-2250DL

Brake Assembly - Dexter Nev-R-Adjust Electric Trailer Brake Kit 12" - Left and Right Hand Assemblies item # 23-464-465

Hub - Dexter Trailer Hub and Drum Assembly - 7K lb E-Z Lube Axle - 12" - 8 on 6-1/2 - 9/16" Studs item # 8-219-18UC3

expert reply by: Jerred H

0

Answer 1

The Dexter Trailer Hub and Drum Assembly part #8-219-18UC3 fits 7K axles and it has a 4.75" pilot with 9/16" studs so it will work with most hub piloted 17.5" wheels like the Provider 215/75R17.5 Radial Tire w/ 17-1/2" Silbrt Mod…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Recommended Bearings, Brake Assembly, and Hub for a Dexter 7,000 lbs Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching