Does Kodiak Brake Line Kit Work with Tie Down 46304 Calipers

Question

Question:

Hi, will this fit a Nitro boat trailer with tie down 46304 calipers. Thanks

asked by: Tim

1

Helpful Expert Reply:

Yes, the Kodiak brake line kit part # bh-3mfs-7 does work with the Tie Down 46304 calipers that you have on your trailer currently.

expert reply by: Jameson C

1

Answer 1

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 2

Sounds like you are trying to install the wrong brake line to the Kodiak Disc Brake Caliper #KDBC225S that you mentioned. The fitting size needs to be 3/16 inch like what comes with the #18TA-BLKIT. Since I don't know what brake lines you have…

view full answer...

Answer 3

We do not have a direct replacement bolt for your Tie Down Engineering 46304 calipers, however if you're able to take a couple quick measurements we can find a replacement bolts for you. For example, the Replacement Guide Bolt for Kodiak Calipers…

view full answer...

Answer 4

I wasn't able to find any confirmation that the dust boot and seal included in the Kodiak Disc Brake Caliper Rebuild Kit #KDBC225KIT were a compatible fit for a Tie Down 46304 caliper, but I did measure them so that if you wanted to check the…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 10

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 11

Hey it sounds like you are on the right track here, Blake. The Kodiak Disc Brake Caliper #KDBC225DAC is exactly what we recommend for replacing the Tie Down 46304 calipers. We have confirmed on multiple occasions that the Kodiak caliper is a suitable…

view full answer...

Answer 12

Hi again David; since TDE is no longer around replacement brake pads are not available for the 46304. However, to avoid complete replacement we have found that the Kodiak Disc Brake Caliper #KDBC225DAC will work as a replacement for the 46304. If you…

view full answer...

Does Kodiak Brake Line Kit Work with Tie Down 46304 Calipers

Product Page this Question was Asked From

Continue Researching