Part Number for L-Pin of Replacement Hardware Kit for Fastway Sway Control Brackets

Question

Question:

Does this l pins the same. FA92-02-9200. As this part fa92-03-9205. I just need l pins and counter pin

asked by: Daniel M

0

Expert Reply:

Yes, the L-pin of the Replacement Hardware Kit for Fastway Sway Control Brackets # FA92-02-9200 that you referenced is the part # FA92-03-9205 that you mentioned.

expert reply by: Jameson C

0

Answer 1

The L-pins on the Fastway e2 systems are a little different than those used with the Equal-I-zer system but #EQ95-01-9430 can be used. For the e2 system we also have replacement L-Pin #FA92-03-9205. The clip is #FA92-04-9208. Each of these are sold…

view full answer...

Answer 2

The replacement L-pin part #FA92-03-9205 that you referenced fits Fastway e2 kits that are 6,000-lb, 8,000-lb, 10,000-lb, or 12,000-lb.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Welcome back Don! The Equal-i-zer Weight Distribution System w/ 4-Point Sway Control item #EQ37120ET is exactly what I would recommend using. This is a solid reliable system and the built in sway control will make a noticeable improvement in ride…

view full answer...

Answer 12

Welcome back Belinda! The Andersen Weight Distribution Hitch w Sway Control - 4" Drop/Rise - 16K GTW, 1.6K TW #AN33VR may work for towing your Grand Design Imagine XLS23LDE with your F-250. However, when we tested it a while back, we didn't…

view full answer...

Part Number for L-Pin of Replacement Hardware Kit for Fastway Sway Control Brackets

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching