Can a Pole Tongue Trailer Be Converted To A-Frame and Strengthen The Frame?

Question

Question:

Can you convert a straight tongue to an A-frame to make it stronger?

asked by: Monique

0

Expert Reply:

Yes, you are able to add additional structure to mount a A-Frame Trailer Coupler # CA-5210-B on a straight tongue trailer. This would make the trailer stronger and less likely to have an issue with the pole tongue sagging from weight.

expert reply by: Bud M

0

Answer 1

In order to determine the correct kit for your trailer I recommend measuring the diameter of your axle. The #K71-384-00 is for a 2-3/8" axle. More than likely you have a 2,000 lb axle with a 1-3/4" diameter. You will need to confirm this.…

view full answer...

Answer 2

I do have all of the components you will need to flip the axle on your tent trailer but there is not an all inclusive kit per se to do so. However, the kits are pretty basic as all they include are u-bolts, tie plates, and spring seats. For your…

view full answer...

Answer 3

Hey Chris, You can flip the axle by just welding on new seat springs to the axle. Dexter has kits for this that include new u-bolts for 2-3/8" #K71-384-00 or 3" #K71-385-00 diameter axles. If you have a smaller axle just let me know and I…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Can a Pole Tongue Trailer Be Converted To A-Frame and Strengthen The Frame?

Product Page this Question was Asked From

Continue Researching