Mounting Bolt Hole Pattern For The Bulldog Powered Drive Trailer Jack # BD500199

Question

Question:

Would like to know the bolt pattern diagram? and diameter of the top mounting plate. My ATC trailer is 3inch O.C. from the frontfoot to the rear two bolts, but 3.25inch O.C. between the rear two bolts. Thank you.

asked by: Mark F

0

Expert Reply:

The Bulldog Powered Drive Trailer Jack # BD500199 has two sets of mounting holes on its mounting flange that are approximately 3.47" apart center-to-center. The two sets are spaced apart approximately 1" center-to-center.

expert reply by: Kevin C

0

BD500199 Mounting Hole Pattern
(click to enlarge)

Answer 1

You are correct in that the Fastec Electric Trailer Jack part FIC 3500 that you have now is rated for 3,500 lbs. It also offers up to an 18" lift. You can certainly use a 4,000 lb jack in place of this and for that, I recommend using the Bulldog…

view full answer...

Answer 2

Your picture didn't make it through and I am not sure what product you are interested in.

view full answer...

Answer 3

The replacement level for your Bulldog Powered Drive Trailer Jack #BD500199 is found as part #BD500193 on our site. It does come with the screws as well.

view full answer...

Answer 4

From the center of the jack tube to the outside edge of the head cover on the Bulldog Powered Drive Trailer Jack #BD500199 is 4",and the head cover extends out 1" from the edges of the jack tube. I've attached some diagrams for you to…

view full answer...

Answer 5

The Replacement Spring Loaded Pull Pin #BD500388 is currently the only spring loaded pull pin that I see available for round jacks. It has only been confirmed to fit the Bulldog Powered Drive Trailer Jack #BD500199 which mounts to a 2" diameter…

view full answer...

Answer 6

I went out to our warehouse to assist with the dimensions of the Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 14" Lift - 4,000 lbs - Black #BD500199. From the top of the mounting plate to the bottom of the motor housing is 12-7/8…

view full answer...

Answer 7

We can only guarantee that the Replacement Spring Loaded Pull Pin #BD500388 would work with Bulldog brand jacks like the Bulldog Velocity powered jack part #BD185400 or the powered a-frame jack #BD500199.

view full answer...

Answer 8

I do have a recommendation for you rather than replacing your Jack #EJ-3520-BBX with one like the Bulldog #BD500199 which can be mounted sideways. You can switch to a longer Ball Mount #BH20 or Shank #EQ90-02-4600 to move your hitch ball further…

view full answer...

Answer 9

I recommend using the etrailer.com Electric Jack with a Footplate, part #EJ-3520-BBX, for A-Frames. This trailer jack is rated for 3,500 lbs so it will have more than enough power to lift and lower your tongue weight of 700 lbs. This trailer jack has…

view full answer...

Answer 10

There is a Bulldog jack that has numerous bolt holes to allow you to unbolt the jack and rotate it 90 degrees, the Bulldog Powered Drive Trailer Jack #BD500199. You can see an example of this in the linked video - just forward to about the 6:15 mark.…

view full answer...

Answer 11

Can you get me the tire size you see printed on the sidewall of the trailer plus the bolt pattern of the wheel? With that I can pick you out the correct size. If you can send me a picture I can try to match the wheel style as well. I noticed you…

view full answer...

Answer 12

On Bulldog electric trailer jack #BD500199 the screw (operated by the motor) travels 14 inches and the drop leg travels 8 inches for a total lift amount of 22 inches. When the jack is fully retracted it measures approximately 9-3/4 inches from the…

view full answer...

Mounting Bolt Hole Pattern For The Bulldog Powered Drive Trailer Jack # BD500199

Featured Help Information

Miscellaneous Media

Continue Researching