Spindle Nut Recommendation for Trailer with 6k Axle

Question

Question:

I have a 2021 Jayco 321rsts. It has 6000lb axles. Do you know the size of the castle nut that holds the flat washer and bearings in place?

asked by: David

0

Expert Reply:

For a 6k trailer axle you'd need a 1 inch diameter spindle nut like the part # 165686 and you'd be set.

expert reply by: Jameson C

0

Answer 1

Most likely you just need to clean the pins of your 7-ways and the error message will go away. It's very common for a bit of corrosion on the connectors to cause an intermittent trailer connection which is what is causing the error message you…

view full answer...

Answer 2

We do have idler hubs as well as hub and drum kits with a 5 on 4-1/2" bolt pattern that fit a 3,500 lb Dexter axle; depending on if you want the idler or hub and drum, you can use one of the following: - Idler Hub: Dexter Trailer Idler Hub…

view full answer...

Answer 3

Yes you can reuse the spindle nut as long as its threads are not ruined and it has good form/fit/function. If you do need a new one or want a spare for future use you can get some here. Replacement Spindle Nut for Dexter Nev-R-Lube Hub and Drum…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Spindle Nut Recommendation for Trailer with 6k Axle

Product Page this Question was Asked From

Continue Researching