Bearing Kit and Brake Assemblies for Lippert 7k Trailer Axle

Question

Question:

Need replacement brakes, bearinga nd seals for 3 lippert 7000 lb axles, the sticker on the axle shows: Variant# V000115575, serial # 045-002009881, customer part # 159091, LC170-SB-92.5=74.5=NOSP-0S-L-86517-7227-18PT, Mfr dATE 11/20/12

asked by: Rick T

0

Expert Reply:

The correct bearing kit with seal that fits your Lippert 7,000 lb trailer axle is the part # BK3-200 that you referenced. Then for a set of left and right brake assemblies you'd want the part # AKEBRK-7-SA for a self adjusting set.

expert reply by: Jameson C

0

Answer 1

For your 7K Lippert Axle I'd go with the etrailer #AKEBRK-7-SA you were looking at. They will be a direct replacement, and will include both sides for one axle, if you have two axles, you're going to need two of these. I really like the…

view full answer...

Answer 2

Is your axle an 8k axle or is it a 4k? If it is an 8k axle then you would want a spring like the part #e89FV but you would have to move in your current hangers. Did you measure your springs with the trailer's weight on the suspension or without?…

view full answer...

Answer 3

The closest leaf spring set we have available to the 22-1/4 inch length you mentioned is the 3-Leaf Double-Eye Spring #SP-113275. This double-eye leaf spring features a length of 23-1/2 inches from the center of the spring eye to the center of the…

view full answer...

Answer 4

Yes, the Tandem Axle Lift Kit #RR23QX that you referenced would be exactly what you would need for your 2019 Eclipse Attitude 28SAG. It will give your trailer a 2 inch lift which would eliminate the nose high situation you are in.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Bearing Kit and Brake Assemblies for Lippert 7k Trailer Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching