Width and Channel Width of Thule ProBars Cover Strip

Question

Question:

Item # TH97JH What is the overall width and the inserted width of this product? I have a set of the sport package roof rack crossbars on my 07 Mercedes ML350 and need the rubber inserts for the slots. Depending on the dimensions, this product might work.

asked by: Robert K

1

Helpful Expert Reply:

The width of the slot gap in the Thule ProBars that uses the Replacement Upper Rubber Cover Strip for Thule ProBar Crossbars # TH97JH is 1/2 inch. The overall width of the channel is 3/4 inch.

expert reply by: Jameson C

1

Answer 1

The part number you mentioned is the Subaru/Thule Aeroblade crossbar so for a replacement rubber strip you would need the part #TH69JH.

view full answer...

Answer 2

The Replacement Top Channel Crossbar Infill for Yakima HD Style Crossbars #Y33KV is the Yakima 8881036 and the correct insert for your Yakima HD Crossbars #Y01158. The Replacement Top Infill #Y01166 is the Yakima part number 8001166 which fits both…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

Hey Hadiya! No, the Curt E16 5th Wheel Hitch w/ S20 Slider for Ram #C85PV will not give you enough clearance to maneuver the Layton Skyline 5th wheel with your 2021 Ram 1500 with a 5-1/2' bed. This unit only moves you 12" back from the…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Width and Channel Width of Thule ProBars Cover Strip

Product Page this Question was Asked From

Continue Researching