Where Can I Find The Drive BT-100 Drive App

Question

Question:

where can i get the app for the BT-100 it is not on the app store

asked by: Sam

0

Expert Reply:

The manufacturer took the app down because it didn't work stating it would be fixed and back up soon. It's been over a year since I read about this so I don't believe they will be fixing it and the best option would be to replace the stereo if the app is crucial to controlling it in your situation.

If that's the case then I recommend the Furrion RV Stereo # DV3300SBL. You will have to trim your cutout hole a bit wider, but this would be the case for every other stereo that we currently carry.

expert reply by: Kevin C

0

Answer 1

The seal you need for your trailer hub is the #58846. Or for a bearing kit that includes all of the components you'll need you'd want the #BK2-100. For brake assemblies you'd want the part #AKEBRK-35L for the left side or part #AKEBRK-35R…

view full answer...

Answer 2

The Drive RV Stereo #324-000148 uses the Drive app you can download. I reached out to my tech contact who walked me through the App Store download. You will search "drive bt" which will pull up two options. You want the Drive BT for your…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Where Can I Find The Drive BT-100 Drive App

Continue Researching