Replacement Brake Pads for Dexter 3,500 lb Trailer Axle

Question

Question:

Do you stock dexter brake pads ufp- db 35 for marine master boat trailers

asked by: Jeff S

0

Expert Reply:

For a Dexter 3,500 lb trailer axle we have the replacement brake pads of part # K71-623-00 which would work fine on a boat trailer.

expert reply by: Jameson C

0

Answer 1

The mounting bracket for the 3.5K Kodiak disc brake kits is #KCMB10HRD. For the bolts to mount the bracket to the brake mounting flange use 4 of #7-75 per bracket. the matching nut is #6-17 and the lock washer is #5-8.

view full answer...

Answer 2

Hello Rob, good question. The difference between the Caliper Brackets #KCMB10RD and #KCMB10HRD is the type of hubs they are intended to work with. The #KCMB10RD should be used with calipers on disc brake assemblies with over-the-hub rotors like part…

view full answer...

Answer 3

There are a couple ways to determine the correct seals to be used on your Dexter axles. Without removing your hubs you can check the axle for a tag which includes the serial number for your axle. With this information I can contact Dexter to get the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Brake Pads for Dexter 3,500 lb Trailer Axle

Continue Researching