Wall Thickness of Draw Tite Hitches # 65022 and # 65005

Question

Question:

Hi do you have the thickness specs for the mounting brackets of these hitches : drawtite 65022 drawtite 65005

asked by: Scott B

0

Expert Reply:

Both the Draw Tite hitches part # 65022 and # 65005 have a wall thickness of 3/8 inch.

expert reply by: Jameson C

0

Answer 1

Thanks for reaching out Denis, I'd love to clear the air for you! While I don't have info on the factory that the Draw-Tite Front Mount Trailer Hitch Receiver #65022 is made at, what I can say is that Draw-Tite is one of the leading hitch…

view full answer...

Answer 2

We have two front mount receivers available for a 2004 F-450 cab and chassis. They are Draw-Tite part #65022 and Curt part #31114. I have added links to these parts and their install instructions below. I did some geometry with your 8 on 9 inch lug…

view full answer...

Answer 3

The Draw-Tite Front Mount Trailer Hitch Receiver #65022 is rated for a 5,000 lb trailer and 500 lbs of tongue weight, and the amount of time isn't a factor. So you wouldn't be able to move a 10,000 lb trailer even if it is swift, as you are…

view full answer...

Answer 4

While we do have a front-mounted trailer hitch receiver that fits a 2003 Ford F-250, the part model you asked about will not fit as it doesn't have the correct dimensions to line up with your truck and there are no brackets that will allow this.…

view full answer...

Answer 5

I can help and there is a front mounted hitch that is a fit for your 2006 Ford F-250 and I recommend the Draw-Tite #65022, which will sit in the opening through the front bumper. It is a 2" hitch with 9,000 lbs of line pull and a vertical load…

view full answer...

Answer 6

I spoke with my contact at Draw-Tite to verify and he said that the OEM fog lights will have to be removed to install Front Mount Receiver, #65022. If you wish to retain the lights they will have to be relocated. I have included a link to the…

view full answer...

Answer 7

The Curt Front Mount Trailer Hitch Receiver #C31014 is the only front receiver that we currently offer for your 2001 Ford F-350 that does not require you to remove the front bumper. For it to mount your F-350 must have the blocker beam on the front.…

view full answer...

Answer 8

The 2002 F-250 has two different styles of front end configurations. If your front end has the blocker beam behind the front bumper and the leaf springs mounted on the inside of the frame rails then you would use the Curt Front Mount Trailer Hitch…

view full answer...

Answer 9

We do indeed have a front mounted receiver that's a fit for the 2001 Excursion, part #65022. The hitch would install directly to the front of the frame members behind the bumper. Installation involves removing the bumper, and sandwiching the…

view full answer...

Answer 10

Hey Bill, so we don't have a direct solution for relocating the fog lights of your 2006 Ford F-250 with the Draw Tite front hitch part #65022 installed but if you check out the attached picture you can see a customer of ours who had some…

view full answer...

Answer 11

I do have a solution for you to install a front hitch on your 2003 Ford F-350 that will lead the OEM fog lights in tact, but you will need to confirm that your truck has the blocker beam behind the bumper (only found on 4wd versions of this truck, so…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Wall Thickness of Draw Tite Hitches # 65022 and # 65005

Continue Researching