Curt CrossWing Lightweight 5th Wheel Trailer Hitch # C92DR Base Dimensions

Question

Question:

What are the dimensions of this hitch’s base?

asked by: Chris

1

Helpful Expert Reply:

I checked with Curt and the footprint dimensions of the base of the Curt CrossWing Lightweight 5th Wheel Hitch part # C92DR are 25.8 inches front to back and then 42 inches from left to right.

expert reply by: Jameson C

1

Crosswing Base Dimensions
(click to enlarge)

Answer 1

The Curt CrossWing Lightweight 5th Wheel Trailer Hitch part #C92DR is a great option for your 2022 Chevrolet Silverado 2500. If you have the factory prep package then all you need is a gooseneck hitch ball like the Curt Ball and Safety Chain Loop Kit…

view full answer...

Answer 2

Jameson's wording could've been better but what he meant was that there isn't any way to adjust the connection point of the Curt CrossWing Lightweight #C92DR since it only allows for you to raise of lower the hitch head. In the question…

view full answer...

Answer 3

Fifth wheel hitches like the #C32DR do not require safety chains so there aren't any brackets on the Curt Crosswing part #C32DR for them. It's an interesting caveat but if there isn't a hitch ball involved safety chains aren't…

view full answer...

Answer 4

The Curt Crosswing part #C86JR does not void any warranties on trailer frames as it's a fifth wheel hitch and not a gooseneck adapter. It's also lighterweight which helps make it an easier choice then most fifth wheel hitches. If you were…

view full answer...

Answer 5

There basically is no difference but we have two part numbers for the Curt Crosswing depending on where we have it listed on our website. As a fifth wheel hitch it's part #C92DR or as an adapter for a gooseneck hitch ball part #C32DR.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Curt CrossWing Lightweight 5th Wheel Trailer Hitch # C92DR Base Dimensions

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching