What Bolt Is Used In The Ultra-Fab Steel Jumbo Roller

Question

Question:

Hi, if I need to replace a bolt, what size bolt would I need. Would like to just have a replacement incase one of the bolts breaks.

asked by: Jennifer V

0

Expert Reply:

The Ultra-Fab Steel Jumbo Roller # UF48-979023 uses a special wet-bolt to grease the skid wheel as needed. This bolt is unfortunately not an item that we currently carry so you would need to reach out to the manufacturer for a replacement. That being said, the hanger or wheel will most likely break before the bolt will.

expert reply by: Kevin C

0

Answer 1

There are really only two standard trailer tire sizes for 15" wheels, 205/75-15 and 225/75-15 with the latter being the taller option (28.4" diameter x 8.9" wide vs. 27.3" diameter x 8.1" wide). I recommend the Karrier…

view full answer...

Answer 2

The Ultra Fab roller part #UF48-979023 do not have a weight capacity. My contact at Ultra-Fab said that because these rollers are not meant to sustain weight for extended periods of time, they do not have a weight capacity stated.

view full answer...

Answer 3

It would be a good time to replace both of your rollers with the part #UF48-979023 that you mentioned. There isn't a set grease schedule for these but if you greased them once a season, or even once at the beginning of the season and once at the…

view full answer...

Answer 4

I might have a solution for you. However, the Ultra Fab 4 Inch Caster Wheels, #UF48-979011, will not be a viable option for your trailer. The best option will be to use the Ultra Fab Steel Jumbo Rollers, #UF48-979023. These roller have a 3 inch long…

view full answer...

Answer 5

The skid wheel part #UF48-979023 would work well for you as it's the largest size we have to fit your trailer. This shouldn't hurt your frame strength either. The more you have the better it will distribute the weight. So going with one on…

view full answer...

Answer 6

The Ultra-Fab Steel Jumbo Roller #UF48-979023 you were looking at comes as a quantity of one, so if you're needing a pair you'll need to order two.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

What Bolt Is Used In The Ultra-Fab Steel Jumbo Roller

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching