Channel Width and Height of Buyers Products Pintle Loop and Channel part # 337B20143

Question

Question:

Can I get the length and width dimensions of the adjustment bracket?

asked by: Colton

1

Helpful Expert Reply:

The overall height of the bracket of the Buyers Products Pintle Loop and Channel part # 337B20143 is 7-5/8 inches. The overall width is 4 inches.

expert reply by: Jameson C

1

Bracket Dimensions of Channel
(click to enlarge)

Answer 1

For the Buyers Products Zinc Plated 10-Ton Forged Steel Lunette Ring w/ 3" I.D. #337B16140Z you are correct that the 5/8 inch bolts are traditionally used for the C-channel. This is partially because the bolts are normally 5-1/2 inches long. The…

view full answer...

Answer 2

You would want to use the 2000 lb rated Timbren Axle-less trailer suspension that you'd looked at, part #ASR2KHDS03 for for the best ride quality. The 3500 lb rated system would make for a very rough ride that you wouldn't be happy with. If…

view full answer...

Answer 3

I would be happy to recommend the correct Timbren axle-less system and electric trailer brake setup for the M416 trailer you are rebuilding. Starting with the Timbren system I recommend the 2000lb system #ASR2KHDS02 which will be plenty highly rated…

view full answer...

Answer 4

I recommend using the Timbren Axle-Less System #ASR1THDS02. This system is similar to the system you were looking at but it has a weight capacity of 2,200 lbs and does not come with any hubs, so you can add compatible 5 on 5 inch hubs like…

view full answer...

Answer 5

The BFGoodrich 33-12.50/15 Tires you are referring to are light truck tires for passenger vehicles which means they cannot be used on a trailer therefore we would not have trailer fenders specially designed to accommodate them. However, the Single…

view full answer...

Answer 6

Thanks for including a picture! Actually, the electric over hydraulic actuators have their own reservoir as the brake line connects directly to the unit. The integrated brake controller you have isn't compatible with electric over hydraulic…

view full answer...

Answer 7

I have a soluton for you, but the Dexter EOH Actuator #K71-651 is designed for disc brakes and the pressure generated for those would damage the components of drum brakes. Instead I recommend using the Dexter #K71-650 which has 1000 psi and is…

view full answer...

Answer 8

I have another option for you, but no you cannot use the Dexter DX EOH Actuator For Disc Brakes #K71-651 with hydraulic drum brakes. This is due to the pressure differences in the actuators as they were designed for the different styles of brakes.…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Channel Width and Height of Buyers Products Pintle Loop and Channel part # 337B20143

Product Page this Question was Asked From

Continue Researching