Recommended 5/8 Inch Hitch Pins for Mounting Lunette Ring in C-Channel Coupler
Published 09/27/2018 >
Products Featured in This Question
Question:
Hi, On my current trailer the lunette ring is bolted with two 5/8 inch bolts and nylock nuts to the c-channel that is welded to the trailer. I need to replace the lunette ring as it is excessively worn. Is there a reason why I have to bolt the lunette ring into the c-channel? Why can I not just use two 5/8 inch hitch pins? Looking at all the adjustable ball hitches I see the same type of geometry using basically hitch pins to hold the ball in the c-channel instead of nuts and bolts. Thanks
asked by: Bill P
Helpful Expert Reply:
For the Buyers Products Zinc Plated 10-Ton Forged Steel Lunette Ring w/ 3" I.D. # 337B16140Z you are correct that the 5/8 inch bolts are traditionally used for the C-channel. This is partially because the bolts are normally 5-1/2 inches long. The standard pins are simply not long enough in most cases and the lunette ring is not tested for use with these pins so you'd most likely be outside of the manufacturer's warranty.
The usable pin length of the Curt 3 inch receiver hitch pin # C21507 is 4-3/4 inches, so it will be more similar to the bolts and should work for your C-channel mount which is 3-1/2 inches outside to outside.
Product Page this Question was Asked From
Buyers Products Zinc Plated 10-Ton Forged Steel Lunette Ring w/ 3" I.D.
- Lunette Ring
- Coupler Only
- Bolt-On
- 20000 lbs GTW
- 3 Inch Lunette Ring
- Buyers Products
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: lunette ring
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 6 on 5-1/2 - Pre-Greased
- Shop: Ark Xtreme Off-Road Swivel Jack w/ Dual Wheel - Sidewind - 10" Lift - 1,100 lbs - Black
- Shop: Buyers Products Zinc Plated 10-Ton Forged Steel Lunette Ring w/ 3" I.D.
- Search Results: pintle hitch
- Q&A: Channel Width and Height of Buyers Products Pintle Loop and Channel part # 337B20143
- Q&A: Timbren Axle Less Kit with Hub that Has Jeep Wrangler Wheel Bolt Pattern
- Q&A: Recommended Timbren Axle-Less System And Electric Trailer Brakes For M416 Trailer
- Q&A: Timbren Axle-Less Suspension Recommended for 1500 lb Homemade Camper
- Search Results: lock and roll
- Search Results: receiver tube
- Search Results: 94655pr
- Video: TruRyde Self-Adjusting Electric Brake Assembly Comprehensive Review
- Q&A: Trailer Fenders for 33 Inch BFGoodrich Mud Tires
- Shop: Buyers Products 3" I.D. Heavy-Duty Forged 4-Bolt Mount Lunette Ring - Black
- Shop: Gen-Y Weld-On 2" Receiver Tube - 12" Long - Steel
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 6 on 5-1/2 - Pre-Greased
- Shop: Buyers Products 3-Position Adjustable Lunette Ring with 3" Heavy-Duty Channel - 10 Ton
- Search Results: trailer jacks
- Search Results: pintle ring
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Suspension Enhancement
- Shop: Brake Controller



